View source for CNC Bender v12.12

<table>
<tr>
<td width=400>
===v12.12 - August 25, 2014===
*Back to [[CNC Bender Software Updates]]
*See [http://advancedtubular.com/customers/cncbender CNC Bender Customer Service Page] for an update.
</td>
<td width=300>
[[image:cncv12procontrol_withteachmode.jpg|300px]]<br>
</td>
<td>
</td>
</tr>
</table>

__NOTOC__

==[[image:Check.jpg|25px]] ENHANCED: CNC Processor - Machine Lube Feature==

<table>
<tr>
<td width=300>

CNC Processor can control machine lube at a lower level.  This enables machine lube to work even when other motion is occurring.  These are the changes for machine lube in this version:<br><br>

* Depending on the style of switch that indicates the lube is complete, lube complete could be configured to either HIGH or LOW.  So now this feature can allow a machine lube switch to be active when it is LOW.<br><br>
* In this version , when the feature is active, and the E-Stop is pressed, the lube is immediately stopped.<br><br>
* New messages for the machine lube are posted in the Processor log in the CNC Bender user interface.<br><br>
<td>
[[image:cncbender_v12.12_machinelube_screenshot.png|500px]]
</td>
</tr>
</table>

<br><br>

==[[image:Check.jpg|25px]] ENHANCED: Part Filename Mode in Keyboard==

<table>
<tr>
<td width=300>

Previous versions of CNC Bender would allow characters in part names that made the part name illegal or caused problems to CNC Bender.<br><br>

* This issue has been resolved in this version with a keyboard that will make the disallowed character buttons to disappear when in the filename mode.<br><br>
* When these characters are pressed on the physical keyboard when this mode is active, then the key presses will be ignored.
<br><br>
The characters filter out are:<br><br>

	* < (less than)
	* > (greater than)
	* : (colon)
	* " (double quote)
	* / (forward slash)
	* \ (backslash)
	* | (vertical bar or pipe)
	* ? (question mark)
	* * (asterisk)
	* = - causes problems with sending data to processor?




<td>
[[image:cnc_v12.11_tubeshape_notclear_toolpage.png|500px]]
</td>
</tr>
</table>

<br><br>

==[[image:Check.jpg|25px]] FIX: Custom Command Editor==

<table>
<tr>
<td width=300>
The Custom Commands menu and Custom Command Editor would sometimes show an error when clearing the menu then re-entering the Editor.<br><br>
This problem has been resolved in this version.

<td width=300>
[[image:cnc_v12.11_customcommand_editor.png|500px]]
</td>
<td>
</td>
</tr>
</table><br><br>


==[[image:Check.jpg|25px]] ENHANCED: CNC Program Loader Allows for Adjustable CNC Executable Location==

<table>
<tr>
<td width=300>
The location of the CNC Bender executable files can change depending on the application.  The Program Loader can now run the CNC Bender program from any location - not just the standard "C:\CNC" folder location.

<td width=300>
[[image:cnc_v12.11_programloader.png|500px]]
</td>
<td>
</td>
</tr>
</table><br><br>

==[[image:Check.jpg|25px]] Other Changes ==

<table>
<tr>
<td width=400>
* Removed the second scroll bar on the right side of the File Load menu since it was redundant.

</td>
<td width=300>
</td>
</tr>
</table>

<br><br>

==Other Pages==
*Back to [[CNC Bender]]
*Back to [[CNC Bender Software Updates]]
*See [http://advancedtubular.com/customers/cncbender/page-downloads/v12-20130830.html CNC Bender Customer Service Page] for an update.
*See [[CNC Bender General Information]]
*See [[Teach Mode]]
*See [[Custom Command]]s