Difference between revisions of "VTube-LASER v1.81.6"
From ATTWiki
| (18 intermediate revisions by one user not shown) | |||
| Line 3: | Line 3: | ||
<td width=225> | <td width=225> | ||
[[image:vtube-laser_logo.jpg|300px]] | [[image:vtube-laser_logo.jpg|300px]] | ||
| − | ==Revision 1. | + | ==Revision 1.81.6== |
* Back to [[VTube-STEP]] | * Back to [[VTube-STEP]] | ||
* Back to [[VTube Software Updates]] (for LASER Mode) | * Back to [[VTube Software Updates]] (for LASER Mode) | ||
| Line 26: | Line 26: | ||
<td width=400> | <td width=400> | ||
| − | We've changed the interface to move the FARO arm utilities into a single window. | + | * We've changed the interface to move the FARO arm utilities into a single window. The Arm Utilities button in the Measure Setup / Arm tab menu loads this window.<br><br> |
[[image:vtube-laser-1.82_armutilitieswindow.jpg|400px]] | [[image:vtube-laser-1.82_armutilitieswindow.jpg|400px]] | ||
| + | * When the window loads, the window takes over the connection the arm and allows you to perform probe setup, calibration, diagnostics, single point accuracy tests, etc.<br><br> | ||
| + | |||
| + | * This fixes a problem where the LLP calibration would not always exit properly. | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | [[image:vtube-laser-1. | + | [[image:vtube-laser-1.82_lasertabmenu_circle_armutilities.jpg|300px]]<br> |
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | <br><br> | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] ENHANCED - New Popup in Part Setup for Overbend and Cut Length Calculators=== | ||
| + | |||
| + | <table cellpadding=10> | ||
| + | <tr valign=top> | ||
| + | <td width=400> | ||
| + | [[image:vtube-1.81.6-partsetup_popup_laser.jpg|400px]]<br> | ||
| + | * This change gives more room to the grid of values to display on the screen without scrolling by removing the two buttons from the bottom of the Part Setup menu.<br><br> | ||
| + | </td> | ||
| + | <td width=300> | ||
| + | [[image:vtube-1.81.6-partsetup_laser.jpg|300px]]<br> | ||
</td> | </td> | ||
</tr> | </tr> | ||
| Line 45: | Line 64: | ||
<td width=400> | <td width=400> | ||
| − | + | * The Connect to Arm feature has been rewritten to make it more robust. It is also now possible to disconnect from the FARO arm at any time using the "Disconnect from Arm" button.<br><br> | |
| + | * Overbend Calculator is now integrated into VTube. The values are now always updated and transferred back to VTube as they are entered in the Overbend.<br><br> | ||
| + | * Supravision export in STEP mode would send an incorrect wall thickness value. This has been resolved.<br><br> | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | + | [[image:vtube-laser-1.82_lasertabmenu_disconnectfromarm.jpg|300px]]<br> | |
</td> | </td> | ||
</tr> | </tr> | ||
Latest revision as of 20:11, 12 June 2013
|
Revision 1.81.6
|
|
- See VTube-LASER Customer Support Page to download the latest version.
NEW: FARO Arm Utilities Window
|
|
ENHANCED - New Popup in Part Setup for Overbend and Cut Length Calculators
|
|
|
Other Changes
|
|
Other
- Back to VTube-STEP
- Back to VTube Software Updates (for LASER Mode)
- Back to VTube-LASER
- See VTube Language Editor
