Difference between revisions of "CNC Bender v12.3"
From ATTWiki
(→25px NEW: Timeout in CYCLE HOLD for Controlled Jogs) |
(→25px Other Changes) |
||
| (5 intermediate revisions by one user not shown) | |||
| Line 2: | Line 2: | ||
<tr> | <tr> | ||
<td width=400> | <td width=400> | ||
| − | ===v12.3 - October | + | ===v12.3 - October 3, 2013=== |
*Back to [[CNC Bender Software Updates]] | *Back to [[CNC Bender Software Updates]] | ||
*See [http://advancedtubular.com/customers/cncbender CNC Bender Customer Service Page] for an update. | *See [http://advancedtubular.com/customers/cncbender CNC Bender Customer Service Page] for an update. | ||
| Line 18: | Line 18: | ||
==[[image:Check.jpg|25px]] FIX: Pulldown ComboBox Fix == | ==[[image:Check.jpg|25px]] FIX: Pulldown ComboBox Fix == | ||
| − | Pulldown boxes could crash CNC Bender when being pulldown. | + | Pulldown boxes could crash CNC Bender when being pulldown. This has been repaired. |
<br><br> | <br><br> | ||
==[[image:Check.jpg|25px]] NEW: Timeout in CYCLE HOLD for Controlled Jogs == | ==[[image:Check.jpg|25px]] NEW: Timeout in CYCLE HOLD for Controlled Jogs == | ||
| − | CNC Bender now times-out controlled jogs even in CYCLE HOLD. | + | CNC Bender now times-out controlled jogs even in CYCLE HOLD if the time-out period is elapsed. |
<br><br> | <br><br> | ||
| + | |||
| + | |||
| + | ==[[image:Check.jpg|25px]] ENHANCED: Direct Axes Jog Button and Image == | ||
| + | |||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=400> | ||
| + | The Direct Axis jog button and large LED image were redesigned so that the button will not overcome the paint event of the LED image.</td> | ||
| + | <td width=300> | ||
| + | [[image:cncv12procontrol_directaxis_greenled.jpg|300px]]<br> | ||
| + | </td> | ||
| + | <td> | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table><br><br> | ||
==[[image:Check.jpg|25px]] Other Changes == | ==[[image:Check.jpg|25px]] Other Changes == | ||
| Line 31: | Line 46: | ||
<tr> | <tr> | ||
<td width=400> | <td width=400> | ||
| + | * Repaired form repaint issue in the Low Level menu. | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
Latest revision as of 13:04, 3 October 2013
v12.3 - October 3, 2013
|
|
FIX: Pulldown ComboBox Fix
Pulldown boxes could crash CNC Bender when being pulldown. This has been repaired.
NEW: Timeout in CYCLE HOLD for Controlled Jogs
CNC Bender now times-out controlled jogs even in CYCLE HOLD if the time-out period is elapsed.
ENHANCED: Direct Axes Jog Button and Image
| The Direct Axis jog button and large LED image were redesigned so that the button will not overcome the paint event of the LED image. |
|
Other Changes
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender Customer Service Page for an update.
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
