Difference between revisions of "Revision: Benderlink for Chiyoda/Keins 6.7"

From ATTWiki
Jump to: navigation, search
(→‎25px ENHANCED - New CONVERSION Menu Option: Ignore Diameters with Zero)
(→‎25px ENHANCED - New CONVERSION Menu Option: Ignore Diameters with Zero)
Line 34: Line 34:
 
<br><br>
 
<br><br>
  
−
==[[image:Check.jpg|25px]] ENHANCED - New CONVERSION Menu Option: Ignore Diameters with Zero ==
+
==[[image:Check.jpg|25px]] ENHANCED - New CONVERSION Menu Option: Check ==
 +
 
 +
<table>
 +
<tr>
 +
<td width=300>
  
 
Benderlink can now ignore radii values of zero by unchecking the option in the main conversion window.<br><br>
 
Benderlink can now ignore radii values of zero by unchecking the option in the main conversion window.<br><br>
Line 43: Line 47:
 
(Rad Level 2) / 1.5<br><br>
 
(Rad Level 2) / 1.5<br><br>
 
If both radius level values are zero, then Benderlink will set the diameter to 1 unit.<br><br>A non-zero diameter is important for when you communicating with ROMER DOCS software because DOCS will report a corrupted file if it senses a zero radius.  (This is not an issue in VTube-LASER - it can ignore the diameter of zero.)
 
If both radius level values are zero, then Benderlink will set the diameter to 1 unit.<br><br>A non-zero diameter is important for when you communicating with ROMER DOCS software because DOCS will report a corrupted file if it senses a zero radius.  (This is not an issue in VTube-LASER - it can ignore the diameter of zero.)
 +
 +
</td>
 +
[[image:benderlink_chiyodakeins_stopforzerodiameter.png|400px]]
 +
<td>
 +
</td>
 +
</tr>
 +
</table>
  
 
==OTHER PAGES==
 
==OTHER PAGES==

Revision as of 00:58, 9 November 2013

Blink keinschiyoda orangefire.jpg

Revision 6.7

Back to Benderlink for Chiyoda
Back to Benderlink for KEINS

Blink keinschiyoda screens 6.1.jpg



Check.jpg ENHANCED - New Serial Port COM Engine Available

This Benderlink can use either the new WinSoft COM engine for faster communications, or the older MarshallSoft COM engine for cases where the older engine works better.

The Benderlink.ini file is found in the c:\Users\[username]\AppData\Roaming\BenderlinkChiyodaKeins folder.

Edit the Benderlink.ini in a notepad editor. The section to change is Communications Setup "COM Engine". These are the two available setups:

[Communications Setup]
COM Engine=WinSoft

or 

[Communications Setup]
COM Engine=Marshallsoft




Check.jpg ENHANCED - New CONVERSION Menu Option: Check

Benderlink chiyodakeins stopforzerodiameter.png

Benderlink can now ignore radii values of zero by unchecking the option in the main conversion window.

If the zero diameter is ignored, then Benderlink will automatically set the diameter to non-zero using this formula:

(Rad Level 1) / 1.5

If the Rad Level 1 value is zero, then Benderlink will use this formula:

(Rad Level 2) / 1.5

If both radius level values are zero, then Benderlink will set the diameter to 1 unit.

A non-zero diameter is important for when you communicating with ROMER DOCS software because DOCS will report a corrupted file if it senses a zero radius. (This is not an issue in VTube-LASER - it can ignore the diameter of zero.)

OTHER PAGES

Retrieved from "http://www.advancedtubular.wiki/index.php?title=Revision:_Benderlink_for_Chiyoda/Keins_6.7&oldid=23245"