Difference between revisions of "CNC Bender v14.9-r10"
(→25px FIX: Mandrel Lube for Positive Bend Direction) |
(→25px ENHANCEMENT: Benderlink Change for ROMER Software) |
||
| (15 intermediate revisions by one user not shown) | |||
| Line 16: | Line 16: | ||
__NOTOC__ | __NOTOC__ | ||
| − | ==[[image:Check.jpg|25px]] ENHANCEMENT: | + | ==[[image:Check.jpg|25px]] ENHANCEMENT: Benderlink Change for ROMER Software Communications == |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
<table> | <table> | ||
| Line 33: | Line 22: | ||
<td width=500> | <td width=500> | ||
| − | Previous versions of CNC Bender would send Supravision data with XYZ values even if the XYZ values had not been setup (and were all zeros).<br><br> | + | Previous versions of CNC Bender Benderlink would send Supravision data with XYZ values even if the XYZ values had not been setup (and were all zeros).<br><br> |
This caused ROMER software products to refuse the incoming data and display an error.<br><br> | This caused ROMER software products to refuse the incoming data and display an error.<br><br> | ||
| − | This release of CNC Bender will automatically remove the XYZ data if they are all zeros. This satisfies the ROMER software rules. | + | '''This release of CNC Bender will automatically remove the XYZ data if they are all zeros. This satisfies the ROMER software rules.''' |
| + | </td> | ||
| + | <td> | ||
| + | [[image:romer_infinite.jpg]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| + | <br><br> | ||
| − | ==[[image:Check.jpg|25px]] | + | ==[[image:Check.jpg|25px]] ENHANCEMENT: Cross Slide Check == |
| − | + | ||
<table> | <table> | ||
<tr> | <tr> | ||
<td width=500> | <td width=500> | ||
| − | + | In previous versions of CNC Bender, the internal logic would not allow the manual jog close of either PRESSURE die or CLAMP die if the Cross Slide input prox for AWAY from die (or in the home position) was active.<br><br> | |
| − | + | This has been changed so that CNC Bender now only examines the Cross Slide input prox for ADVANCED or IN the die active.<br><br> | |
| + | '''This allows for locking the carriage cross slide for little or no movement - with both HOME and ADVANCED proximity switches active at the same time - and still close the dies.''' | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:cncbender_crossslide.png|400px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | |||
| − | |||
<br><br> | <br><br> | ||
Latest revision as of 14:36, 12 March 2016
v14.9-r10 - March 10, 2015
|
|
ENHANCEMENT: Benderlink Change for ROMER Software Communications
|
Previous versions of CNC Bender Benderlink would send Supravision data with XYZ values even if the XYZ values had not been setup (and were all zeros). |
|
ENHANCEMENT: Cross Slide Check
|
In previous versions of CNC Bender, the internal logic would not allow the manual jog close of either PRESSURE die or CLAMP die if the Cross Slide input prox for AWAY from die (or in the home position) was active. |
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender Customer Service Page for an update.
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
