Difference between revisions of "CNC Bender v15.10.1"
From ATTWiki
(→25pxFIX: QUICK GALIL DISABLE THEN RE-ENABLE) |
|||
| (5 intermediate revisions by one user not shown) | |||
| Line 17: | Line 17: | ||
==[[image:Check.jpg|25px]]ENHANCED: FASTER GALIL AXIS ENABLE== | ==[[image:Check.jpg|25px]]ENHANCED: FASTER GALIL AXIS ENABLE== | ||
Galil axis enables could take up to a second per axis on slower controls. This has been changed so that all axes are enabled simultaneously for a much faster enable. | Galil axis enables could take up to a second per axis on slower controls. This has been changed so that all axes are enabled simultaneously for a much faster enable. | ||
| + | <br><br> | ||
==[[image:Check.jpg|25px]]ENHANCED: FASTER GALIL AXIS DISABLE== | ==[[image:Check.jpg|25px]]ENHANCED: FASTER GALIL AXIS DISABLE== | ||
Galil axis disables were called to invididually taking too much time. This has been changed so that all axes are disable simultaneously. | Galil axis disables were called to invididually taking too much time. This has been changed so that all axes are disable simultaneously. | ||
| + | <br><br> | ||
==[[image:Check.jpg|25px]]FIX: QUICK GALIL DISABLE THEN RE-ENABLE== | ==[[image:Check.jpg|25px]]FIX: QUICK GALIL DISABLE THEN RE-ENABLE== | ||
The Galil would shutdown if the operator disabled axes then enabled them very quickly. This has been resolved by puttina 1.5 second delay before the axis disable is allowed. If the operator presses Cycle Start within that time period, then the disable command is skipped | The Galil would shutdown if the operator disabled axes then enabled them very quickly. This has been resolved by puttina 1.5 second delay before the axis disable is allowed. If the operator presses Cycle Start within that time period, then the disable command is skipped | ||
| + | <br><br> | ||
==[[image:Check.jpg|25px]]FIX: BENDERLINK TRANSMISSION of ONE BEND PART== | ==[[image:Check.jpg|25px]]FIX: BENDERLINK TRANSMISSION of ONE BEND PART== | ||
| − | |||
| − | |||
| − | |||
| − | |||
CNC Bender would not transmit one bend parts in Supravision. This has been fixed. | CNC Bender would not transmit one bend parts in Supravision. This has been fixed. | ||
| − | < | + | <br><br> |
| − | < | + | |
| − | + | ||
| − | + | ||
| − | + | ||
==[[image:Check.jpg|25px]]FIX: BOOLEAN Parameter in Processlist== | ==[[image:Check.jpg|25px]]FIX: BOOLEAN Parameter in Processlist== | ||
| − | |||
| − | |||
| − | |||
| − | |||
Using boolean Dynamic Option parameters (to see if an option is on or off), would shutdown CNC Processor. This has been resolved. | Using boolean Dynamic Option parameters (to see if an option is on or off), would shutdown CNC Processor. This has been resolved. | ||
| − | < | + | <br><br> |
| − | < | + | |
| − | + | ||
| − | + | ||
| − | + | ||
==[[image:Check.jpg|25px]]FIX: CUSTOM UNLOAD== | ==[[image:Check.jpg|25px]]FIX: CUSTOM UNLOAD== | ||
| − | |||
| − | |||
| − | |||
| − | |||
Custom Unload no longer automatically calls to bend arm return to home. | Custom Unload no longer automatically calls to bend arm return to home. | ||
| − | < | + | <br><br><br> |
| − | < | + | |
| − | < | + | |
| − | + | ||
| − | + | ||
==Other Pages== | ==Other Pages== | ||
Latest revision as of 19:05, 12 February 2018
v15.10.1 - February 9, 2018
|
|
ENHANCED: FASTER GALIL AXIS ENABLE
Galil axis enables could take up to a second per axis on slower controls. This has been changed so that all axes are enabled simultaneously for a much faster enable.
ENHANCED: FASTER GALIL AXIS DISABLE
Galil axis disables were called to invididually taking too much time. This has been changed so that all axes are disable simultaneously.
FIX: QUICK GALIL DISABLE THEN RE-ENABLE
The Galil would shutdown if the operator disabled axes then enabled them very quickly. This has been resolved by puttina 1.5 second delay before the axis disable is allowed. If the operator presses Cycle Start within that time period, then the disable command is skipped
FIX: BENDERLINK TRANSMISSION of ONE BEND PART
CNC Bender would not transmit one bend parts in Supravision. This has been fixed.
FIX: BOOLEAN Parameter in Processlist
Using boolean Dynamic Option parameters (to see if an option is on or off), would shutdown CNC Processor. This has been resolved.
FIX: CUSTOM UNLOAD
Custom Unload no longer automatically calls to bend arm return to home.
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
