Difference between revisions of "DOCS"
(→Principles for Communication with SVNET) |
(→Principles for Communication with SVNET) |
||
| Line 147: | Line 147: | ||
</td> | </td> | ||
<td bgcolor="#8ecaae"> | <td bgcolor="#8ecaae"> | ||
| − | If a matching part number is found in memory in DOCS, then DOCS applies the incoming bender data to the CORRECTED LRA data. <br><br> | + | #If a matching part number is found in memory in DOCS, then DOCS applies the incoming bender data to the CORRECTED LRA data. <br><br> |
| − | If the part number DOES NOT MATCH, then DOCs may assume that you intend to create a new MASTER part with the incoming data - and update the NOMINAL data. | + | #If the part number DOES NOT MATCH, then DOCs may assume that you intend to create a new MASTER part with the incoming data - and update the NOMINAL data. |
</td> | </td> | ||
</tr> | </tr> | ||
Revision as of 06:21, 21 December 2007
DOCS is a software package that is sold by Romer. The word "DOCS" means Data Overlay Camera System. Read more about DOCS at these sites:
- At the Hexagon Metrology Web Site: http://www.hexagonmetrology.com.mx/docs?Itemid=34
- At the Romer Web Site: http://us.romer.com/docs-data-overlay-camera-system?Itemid=31
- Tube Shop Manager (Version 2.2 and higher): http://us.romer.com/press-releases/docs-2-2-with-tube-shop-manager?Itemid=15
Contents |
Screen Image
This is a screen image from our test license of DOCS software.
Comparing DOCS to Supravision
Supravision and DOCS are developed by Romer. Supravision is an older program that is quite stable. The DOCS software is much newer.
|
DOCS Software |
Supravision Software |
|
Active - Continued development |
Static - No more development |
|
Allows for the measurement of tube data and non-tube data surrounding the tube - including brackets and other fabrications |
Measures only tube shapes |
|
Can use contact or non-contact measurement |
Can only use non-contact measurement of tube shapes |
|
Can measure multiple tubes in a single DOCS file |
Can measure one tube per Supravision file |
|
We have no experience with DOCS beyond a demo. It appears to be fairly simple to setup for tube measurement. |
Measuring tube shapes is simple after you understand the structure of Supravision menus. |
Our Recommendation
As of December, 2007, we have been given a license of DOCS software for evaluation and testing with our Benderlink software.
This software is moderately stable and is capable of Supravision network communications. In comparing the two packages, we recommend that tube fabricators choose DOCS over Supravision because of the new capabilities within DOCS.
Communication with Supravision Network Protocol
See this link for information on which version of DOCS will communicate using SVNET: [1]
Principles for Communication with SVNET
|
Principles |
Reasons |
|
If the data at the bender control has changed and...
|
A RECALL from a bender clears the results of a measure - so it is important to RECALL the latest bender data from the bender as a first step through Benderlink if the CLRA data in DOCS does not match the bender's LRA values. If the bender data has changed at the bender control before the current part is measured for correctness, then follow these steps:
|
|
After a RECALL from the bender...
|
|
|
Can use contact or non-contact measurement |
Can only use non-contact measurement of tube shapes |
|
Can measure multiple tubes in a single DOCS file |
Can measure one tube per Supravision file |
|
We have no experience with DOCS beyond a demo. It appears to be fairly simple to setup for tube measurement. |
Measuring tube shapes is simple after you understand the structure of Supravision menus. |
