Difference between revisions of "CNC Bender v12.8"
From ATTWiki
(→25px FIXED: Teach Mode and Custom Commands Issue Solved) |
(→25px ENHANCED: Option List Panels Now Clear if no Options Are Present)) |
||
| (14 intermediate revisions by one user not shown) | |||
| Line 2: | Line 2: | ||
<tr> | <tr> | ||
<td width=400> | <td width=400> | ||
| − | ===v12.8 - February | + | ===v12.8 - February 25, 2014=== |
*Back to [[CNC Bender Software Updates]] | *Back to [[CNC Bender Software Updates]] | ||
*See [http://advancedtubular.com/customers/cncbender CNC Bender Customer Service Page] for an update. | *See [http://advancedtubular.com/customers/cncbender CNC Bender Customer Service Page] for an update. | ||
| Line 20: | Line 20: | ||
<table> | <table> | ||
<tr> | <tr> | ||
| − | <td width= | + | <td width=400> |
| + | |||
| + | <h4><b>If you have a hand-bender controlled by CNC Bender and you use custom commands for the ROTATE axis, then this upgrade is important to you.</b></h4> | ||
| + | |||
Custom commands can be entered after every bend in the FRB page. SMT discovered a that FEED and ROTATE commands would not be completed properly when coming out of a custom move.<br><br> | Custom commands can be entered after every bend in the FRB page. SMT discovered a that FEED and ROTATE commands would not be completed properly when coming out of a custom move.<br><br> | ||
| − | * For example, the ROTATE was programmed at 90 degrees. The custom move is 89 degrees - so the finish up command should be set to 1 degree to come to the full 90. However, the finish-up command | + | * For example, the ROTATE was programmed at 90 degrees. The custom move is 89 degrees - so the finish up command should be set to 1 degree to come to the full 90. However, the finish-up command was 90 degrees - which caused the rotate to move to 89 + 90 = 179 degrees.<br><br> |
| − | * This problem occurred on benders where the ROTATE axis is set to a non-standard machine axis 3 | + | * This problem occurred on benders where the ROTATE axis is set to a non-standard machine axis 3 because the machine axis number "2" was hard coded into the process list builder.<br><br> |
* Process list builder now has logic that anticipates that the machine axis number for any motion actuator can change depending on the application. | * Process list builder now has logic that anticipates that the machine axis number for any motion actuator can change depending on the application. | ||
| − | |||
| − | |||
<td> | <td> | ||
| + | [[image:smt_handbender.png|400px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
| − | </table | + | </table> |
| − | ==[[image:Check.jpg|25px]] | + | <br><br> |
| + | <br><br> | ||
| + | |||
| + | ==[[image:Check.jpg|25px]] FIX: Option List Panels Now Clear if no Options Are Present)== | ||
<table> | <table> | ||
<tr> | <tr> | ||
<td width=300> | <td width=300> | ||
| − | + | </td> | |
| − | + | ||
<td width=300> | <td width=300> | ||
[[image:cncbender_OptionPanelCleared.png|600px]] | [[image:cncbender_OptionPanelCleared.png|600px]] | ||
Latest revision as of 20:21, 16 July 2014
v12.8 - February 25, 2014
|
|
FIXED: Teach Mode and Custom Commands Issue Solved
If you have a hand-bender controlled by CNC Bender and you use custom commands for the ROTATE axis, then this upgrade is important to you.Custom commands can be entered after every bend in the FRB page. SMT discovered a that FEED and ROTATE commands would not be completed properly when coming out of a custom move.
|
|
FIX: Option List Panels Now Clear if no Options Are Present)
|
|
Other Changes
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender Customer Service Page for an update.
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
