CNC Bender Software Updates
From ATTWiki
|
|
|
See CNC Bender Upgrade Service page for details on our upgrade service for CNC Bender.
Software Updates
CNC Bender - Fourth Quarter - 2009
| November 18, 2009 | CNC Bender v11-20091118 | Improvements for features from 20091104 version and 20090518 version |
| November 12, 2009 | CNC Bender v11-20091112 | Added dedicated TIMEOUT for Wait for Not End Cycle |
| November 4, 2009 | CNC Bender v11-20091104 | Optimizations aimed to trim 2 to 4 seconds off each part cycle |
| October 22, 2009 | CNC Bender v11-20091022 | Push Bend Profile Setup NAME, PDA-RVG Profile Setup NAME, Keyboard Repair |
| October 19, 2009 | CNC Bender v11-20091019 | Keyboard filtering, Automatic Adjust from Other Benders, Push Bend Profile Enhancements, PDA-RVG Profile Enhancements |
| October 7, 2009 | CNC Bender v11-20091007 | Spacebar filtering, Reset Rotate Enable/Disable, PID Tuning On/Off |
CNC Bender - Third Quarter - 2009
| September 28, 2009 | CNC Bender v11-20090928 | Absolute Rotate during Final Feed Clearance Move, New Mandrel Retract for Part Release |
| September 23, 2009 | CNC Bender v11-200900923 | CNC Bender now shuts motor down even if in CYCLE HOLD, Optimized Absolute Rotate |
| September 15, 2009 | CNC Bender v11-200900915 | Optimized Pressure Die commands based on low level setup plus enhancements. |
| August 27, 2009 | CNC Bender v11-20090827 | Now secondary processes can use [CYCLEHOLD] to put benders in the hold state. |
| August 26, 2009 | CNC Bender v11-20090826 | New "End Cycle" Mode can be switched by external processes |
| August 19, 2009 | CNC Bender v11-20090819 | New set Manual, Step, or Auto Modes for Stack Lights |
| July 29, 2009 | CNC Bender v11-20090729 | Refined Side Loader and Hopper options, New Kicker option |
| July 1, 2009 | CNC Bender v11-20090701 | New FRB copy feature for serpentine parts |
CNC Bender - Second Quarter - 2009
| June 26, 2009 | CNC Bender v11-20090626 | Tool page fix for toolbox, Single radius shifting fix |
| June 09, 2009 | CNC Bender v11-20090609 | Seam Detect MODE, redesigned message window, new formula operators, new BEGIN timers, new PreEnable process list, new Automatic Chuck Close |
| June 05, 2009 | CNC Bender v11-20090605 | Minor debug in repair of the horizontal shift [IF] logic |
| May 28, 2009 | CNC Bender v11-20090528 | Minor debug in displaying proper units for calculation of XYZ to FRB |
| May 18, 2009 | CNC Bender v11-20090518 | Minor debug allowing for AllDiesToClose After motion-controlled PDA return |
| May 15, 2009 | CNC Bender v11-20090515 | Infinitely variable radius with twist, Make contiguous push bend profile sections to form complex part |
| April 08, 2009 | CNC Bender v11-20090408 | The MANDREL is now controlled PER BEND (rather than OVERALL) |
CNC Bender - First Quarter - 2009
| March 30, 2009 | CNC Bender v11-20090330 | Enhanced for Processlist Compiler - Optimized Radius Shifting Logic |
| March 26, 2009 | CNC Bender v11-20090326 | Increased Flexibility: Changed "Feed Away From Dies" Logic to "Radius Shift Away", Moved from OVERALL options to RADIUS options |
| March 20, 2009 | CNC Bender v11-20090320 | Enhanced for Processlist Compiler - Carriage Radius Level Logic |
| February 10, 2009 | CNC Bender v11-20090210 | Fix for Processlist Compiler - PreCommand Commands |
| January 26, 2009 | CNC Bender v11-20090126 | New Load and Save in Tool Page, Low Level Option Rewording for Clarification |
CNC Bender - Last Quarter - 2008
| January 20, 2009 | CNC Bender v11-20090120 | Multitasking process enhancements |
| December 30, 2008 | CNC Bender v11-20081230 | Helical Hitch Feed Push Bending for extended lengths, Precision Gearing of Twist |
| December 18, 2008 | CNC Bender v11-20081218 | New Cycle Time Log |
| December 16, 2008 | CNC Bender v11-20081216 | Better log handling |
| December 11, 2008 | CNC Bender v11-20081211 | New smarter radius shifting, updated CIO.exe |
CNC Bender - Fall 2008
| November 6, 2008 | CNC Bender v11-20081106 | Fixes to PDA Motion return home|
| October 9, 2008 | CNC Bender v11-20081009 | New "recent parts" list in File Open menu |
| October 8, 2008 | CNC Bender v11-20081008 | PreLoad works even without a side loader |
| October 1, 2008 | CNC Bender v11-20081001 | Direct Axis Jog Clipboard - Jog an axis from any screen, Unlimited radius levels |
CNC Bender - September 2008
- Adjust the PDA GEARING RATIO to the Bend axis in REAL-TIME in response to the bend angle
- Unlimited Axis Expansion
- Options Toolbox
| September 23, 2008 | CNC Bender v11-20080923 |
| September 19, 2008 | CNC Bender v11-20080918 |
| September 15, 2008 | CNC Bender v11-20080915 |
CNC Bender - Summer 2008
These versions are for horizontal draw-bending and horizontal push-bending.
| August 23, 2008 | CNC Bender v11-20080823 | |
| August 22, 2008 | CNC Bender v11-20080822 | |
| August 13, 2008 | CNC Bender v11-20080813 | |
| July 29, 2008 | CNC Bender v11-20080729 | |
| July 25, 2008 | CNC Bender v11-20080725 | Helical Coil Bending Introduced |
| July 15, 2008 | CNC Bender v11-20080715 | |
| April 25, 2008 | CNC Bender v11-20080424 | Push Bending Introduced |
CNC Bender - January-April 2008
| April 15, 2008 | CNC Bender v10-20080415 |
| April 10, 2008 | CNC Bender v10-20080410 |
| April 7, 2008 | CNC Bender v10-20080407 |
| March 29, 2008 | CNC Bender v10-20080329 |
| March 19, 2008 | CNC Bender v10-20080319 |
| February 26, 2008 | CNC Bender v10-20080226 |
| February 19, 2008 | CNC Bender v10-20080219 |
| February 14, 2008 | CNC Bender v10-20080214 |
| February 7, 2008 | CNC Bender v10-20080207 |
| January 8, 2008 | CNC Bender v10-20080108 |
CNC Bender - July-December 2007
| December 17, 2007 | CNC Bender v10-20071217 |
| November 20, 2007 | CNC Bender v10-20071120 |
| October 30, 2007 | CNC Bender v10-20071030 |
| October 3, 2007 | CNC Bender v10-20071003 |
| September 28, 2007 | CNC Bender v10-20070928 |
| September 20, 2007 | CNC Bender v10-20070920 |
| September 14, 2007 | CNC Bender v10-20070914 |
| August 28, 2007 | CNC Bender v10-20070828 |
| August 3, 2007 | CNC Bender v10-20070803 |
| July 26, 2007 | CNC Bender v10-20070726b |
| July 11, 2007 | CNC Bender v10-20070711 |
| July 5, 2007 | CNC Bender v10-20070705 |
| July 2, 2007 | CNC Bender v10-20070702 |
|
As of July 2, 2007, the ProControl and LiteControl were combined into one development platform. All changes to one platform automatically effect the other platform |
For ProControl Only
| March 30, 2007 | CNC Bender ProControl 10-20070330 |
| March 15, 2007 | CNC Bender ProControl 10.0.6.2 |
| November 6, 2006 | CNC Bender ProControl 10.0.6.0jkm |
| October 27, 2006 | CNC Bender ProControl 10.0.6.0i |
| July 17, 2006 | CNC Bender ProControl 10.0.5.9 |
| May 15, 2006 | CNC Bender ProControl 10.0.5.7e |
For Older LiteControl on 800x600 Screens
| September 5, 2008 | CNC Bender LiteControl 10.0.6.0 |
| May 30, 2008 | CNC Bender LiteControl 10.0.5.9g |
Other Pages
Back to CNC Bender page
See CNC Bender Upgrade Service page for details on our upgrade service for CNC Bender.
