Difference between revisions of "CNC Bender v11-20090408"
| Line 10: | Line 10: | ||
<br><br> | <br><br> | ||
This new PER BEND feature is critical for mandrels in rectangular or square tubing that rotate 90 degrees, but the mandrel can only bend in one of the two planes. | This new PER BEND feature is critical for mandrels in rectangular or square tubing that rotate 90 degrees, but the mandrel can only bend in one of the two planes. | ||
| − | |||
| − | |||
| − | |||
| − | |||
<br><br> | <br><br> | ||
[[image:bendoptions_mandrel_titlechange.jpg|500px]] | [[image:bendoptions_mandrel_titlechange.jpg|500px]] | ||
| Line 19: | Line 15: | ||
When loading older CNC Bender part files, the new Bend row mandrel option will always be set to OFF. To set the mandrel ON in every row, set the value to ON in one row, then press the "Copy Value to All Rows" button. | When loading older CNC Bender part files, the new Bend row mandrel option will always be set to OFF. To set the mandrel ON in every row, set the value to ON in one row, then press the "Copy Value to All Rows" button. | ||
<br><br> | <br><br> | ||
| − | |||
===[[image:Check.jpg|25px]] ENHANCED - MANDREL CYLINDER ENABLE changed to MANDREL CYCLE ENABLE=== | ===[[image:Check.jpg|25px]] ENHANCED - MANDREL CYLINDER ENABLE changed to MANDREL CYCLE ENABLE=== | ||
Revision as of 14:08, 14 April 2009
ENHANCED - MANDREL CYCLE is now Handled PER BEND
This change allows the mandrel to be switched ON or OFF individually for any bend row rather than for the entire part.
This new PER BEND feature is critical for mandrels in rectangular or square tubing that rotate 90 degrees, but the mandrel can only bend in one of the two planes.
When loading older CNC Bender part files, the new Bend row mandrel option will always be set to OFF. To set the mandrel ON in every row, set the value to ON in one row, then press the "Copy Value to All Rows" button.
ENHANCED - MANDREL CYLINDER ENABLE changed to MANDREL CYCLE ENABLE
The option was RENAMED to "MANDREL CYCLE ENABLE" because we cannot no longer anticipate that all mandrel actuators will be cylinders. For example, it is possible that we may use geared electric servo motors for the mandrel. This is the option list with the new title. Cylinder is changed to Cycle:
CHANGE - Added "RETURN" before "Angle" in "Early Mandrel Forward At Angle"
This option title change to "Early Mandrel Forward at Return Angle" removes an ambiguity on when this feature will take effect. The word "Return" indicates that it happens when the bend arm is RETURNING to setup for the next row.
CHANGE - To Mandrel Early Advance in Prebend Logic
Now the Mandrel Early Advance is activated only if the MANDREL CYCLE ENABLE is ON in the first bend row. (See above)
ENHANCE - New Remark in Processlist For Mandrel Retract Override
To aid in processlist logic diagnostics, the processlist builder now includes a special message in the PREBEND section of the processslist when these mandrel cycle conditions exist:
- The MANDREL TYPE is anything other than NONE (In the Low Level)
- The HOLD MANDREL FORWARD setting is ENABLED in the LAST BEND ROW.
When these two conditions are true, then Mandrel Retract is ALWAYS SKIPPED in the PREBEND section of the processlist. To remind operators of this effect caused by the two option settings, we now insert two remarks in the processlist where the MandrelRetract command would have been inserted:
// ** MANDREL RETRACT OVERRIDE: "Hold Mandrel Forward" setting is ON in the last Bend. ** // ** MANDREL RETRACT OVERRIDE: The mandrel retract is NOT inserted. **
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- Read about Push Bending
- Read about Push Bend Profile Tables
