Difference between revisions of "Revision: Benderlink for BLM 4"
From ATTWiki
| (28 intermediate revisions by one user not shown) | |||
| Line 12: | Line 12: | ||
===[[image:Check.jpg|25px]] NEW - Completely Redesigned Interface=== | ===[[image:Check.jpg|25px]] NEW - Completely Redesigned Interface=== | ||
| − | The interface has been updated and reorganized for easier reading. | + | The interface has been updated and reorganized for easier reading with many new features for ease-of-use. |
<br> | <br> | ||
| − | [[image:blinkblm_v4.jpg| | + | [[image:blinkblm_v4.jpg|600px]] |
| + | |||
| + | *New - Quick Load and Merge BLM Buttons | ||
| + | *New - Large LED numbers that indicate, in real-time, the byte count coming or going. | ||
| + | *New - Large Monitor speed button for switching between MONITOR ON/OFF for waiting on measuring center commands. | ||
| + | *New - Four new Date/Time labels show when data was last transmitted in any direction | ||
| + | *New - Attention Grabber Logs that flash when the operator should know that something important just happened in the logs | ||
<br><br> | <br><br> | ||
| − | |||
| − | |||
| − | + | ===[[image:Check.jpg|25px]] ENHANCED - Updated Eaton Leonard Protocol Handling=== | |
| + | This Benderlink now communicates with Eaton Leonard measuring centers using our new current-loop technology that is compatible with the Eaton Leonard legacy protocol. The new engine for communication handling is much improved over older versions. | ||
| − | + | <br> | |
| + | [[image:vector_tube_data_center.jpg|300px]] | ||
| − | + | ===[[image:Check.jpg|25px]] NEW - New Help and Manual=== | |
| − | + | The manual and help system are completely rewritten with new information that includes... | |
| − | + | ||
| − | + | * how to install Benderlink | |
| + | * how to install the Benderlink Ethernet Module | ||
| + | * how to use the software - in much more depth | ||
| + | [[image:blinkblm_help.jpg|350px]] | ||
<br><br> | <br><br> | ||
| − | |||
| − | + | [http://advancedtubular.com/blink_blm/help_html/ Read the online HELP]<br> | |
| − | <br> | + | [[image:blinkblm_online_help.jpg|400px]] |
| − | [[image: | + | |
| + | |||
| + | |||
<br><br> | <br><br> | ||
| − | + | ||
| + | ===[[image:Check.jpg|25px]] NEW - Edit the BLM YBC Data Before Sending the Corrected Data to the Bender=== | ||
| + | |||
| + | This new capability allows the user to fine-tune the corrections before they are sent to the BLM. For example, a 270 degree rotation can be switched to a -90 degree rotation with the press of an inversion button. | ||
<br> | <br> | ||
| − | [[image: | + | [[image:blinkblm_editdata.jpg|350px]] |
| + | <br><br> | ||
| + | [[image:blinkblm_editdata2.jpg|350px]] | ||
| + | <br><br> | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] New - Check for Matching Part Number - Either ON or OFF=== | ||
| + | |||
| + | This new feature allows you indicate whether you want the part number to match between the BLM and measuringc enter: | ||
| + | |||
| + | *UNCHECK: to setup new parts and ignore the part number during transmission. | ||
| + | *CHECK: To prevent accidental mixing of two parts by making the two systems pay attention to the part name.<br><br> | ||
| + | |||
| + | [[image:blinkblm_checkformatching part number.jpg|350px]] | ||
<br><br> | <br><br> | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] New - Confirmation PING for the Benderlink Module=== |
| + | |||
| + | This allows Benderlink to check for a PING response from a Benderlink Ethernet Module. If the Benderlink Ethernet Module responds to a PING, then it is ready for communication with Benderlink. This test makes testing networks much easier.<br><br> | ||
| + | |||
| + | [[image:blinkblm_confirmationping.jpg|350px]][[image:blink_ethernet_module_vector_benderside_600.jpg|250px]] | ||
| − | |||
<br><br> | <br><br> | ||
| − | [[image: | + | ===[[image:Check.jpg|25px]] New - Setup and Diagnostic Utilities for the Benderlink Ethernet Module=== |
| + | |||
| + | The Benderlink Ethernet Module support software is included in the interface of Benderlink for easy access.<br><br> | ||
| + | |||
| + | [[image:blinkblm_newsetupmenu.jpg]] | ||
<br><br> | <br><br> | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] New - Date and Time in Status Bar=== | ||
| + | |||
| + | The current date and time are now always displayed in the status bar<br><br> | ||
| + | |||
| + | [[image:blinkblm_datetime_status.jpg|600px]] | ||
==Other Pages== | ==Other Pages== | ||
Latest revision as of 08:19, 17 April 2009
|
|
|
NEW - Completely Redesigned Interface
The interface has been updated and reorganized for easier reading with many new features for ease-of-use.
- New - Quick Load and Merge BLM Buttons
- New - Large LED numbers that indicate, in real-time, the byte count coming or going.
- New - Large Monitor speed button for switching between MONITOR ON/OFF for waiting on measuring center commands.
- New - Four new Date/Time labels show when data was last transmitted in any direction
- New - Attention Grabber Logs that flash when the operator should know that something important just happened in the logs
ENHANCED - Updated Eaton Leonard Protocol Handling
This Benderlink now communicates with Eaton Leonard measuring centers using our new current-loop technology that is compatible with the Eaton Leonard legacy protocol. The new engine for communication handling is much improved over older versions.
NEW - New Help and Manual
The manual and help system are completely rewritten with new information that includes...
- how to install Benderlink
- how to install the Benderlink Ethernet Module
- how to use the software - in much more depth
NEW - Edit the BLM YBC Data Before Sending the Corrected Data to the Bender
This new capability allows the user to fine-tune the corrections before they are sent to the BLM. For example, a 270 degree rotation can be switched to a -90 degree rotation with the press of an inversion button.
New - Check for Matching Part Number - Either ON or OFF
This new feature allows you indicate whether you want the part number to match between the BLM and measuringc enter:
- UNCHECK: to setup new parts and ignore the part number during transmission.
- CHECK: To prevent accidental mixing of two parts by making the two systems pay attention to the part name.
New - Confirmation PING for the Benderlink Module
This allows Benderlink to check for a PING response from a Benderlink Ethernet Module. If the Benderlink Ethernet Module responds to a PING, then it is ready for communication with Benderlink. This test makes testing networks much easier.
New - Setup and Diagnostic Utilities for the Benderlink Ethernet Module
The Benderlink Ethernet Module support software is included in the interface of Benderlink for easy access.
New - Date and Time in Status Bar
The current date and time are now always displayed in the status bar
Other Pages
- Go back to Benderlink
- Go back to Benderlink for BLM
- Go to the main Benderlink for BLM page
- About BLM Group USA
