Difference between revisions of "Feed Axis Faults During Feed Bending"

From ATTWiki
Jump to: navigation, search
(→‎Diagnostics)
(→‎Diagnostic 2 - Check the Feed Axis % Values)
 
(6 intermediate revisions by one user not shown)
Line 6: Line 6:
 
<br>
 
<br>
  
−
==Diagnostic 1==
+
==Diagnostic 1 - Check the Bend Die Radius Values==
  
 
<table>
 
<table>
 
<tr>
 
<tr>
 
<td width="200">
 
<td width="200">
−
CHECK THE CENTERLINE RADIUS in the Tool Page.<br>
 
 
Possible Problem: The Centerline Radius values do not to match the bend die radii on the bender.
 
Possible Problem: The Centerline Radius values do not to match the bend die radii on the bender.
 
<br><br>
 
<br><br>
Line 23: Line 22:
 
</table>
 
</table>
  
−
<
+
==Diagnostic 2 - Check the Feed Axis % Values==
 
<table>
 
<table>
 
<tr>
 
<tr>
Line 33: Line 32:
 
Here's an example:
 
Here's an example:
  
−
*8.147" of calculated feed motion for 155.6 degrees of bend
+
*At Feed Adjust Percent of 0%, the calculated feed motion for 155.6 degrees of bend is 8.1"<br><br>
−
*7.000" of measured feed motion
+
*However the actual motion of the Feed axis is 7.5"<br><br>
−
<hr>
+
*The Feed Adjust Percent is therefore -7.4<br><br>
−
That calculates to -14% elongation
+
 
 +
Enter that value into the Feed Adjust Percent field and press AutoBuild
  
 
</td>
 
</td>
 
<td>
 
<td>
−
[[image:cncbender_toolpage_radius.jpg|550px]]
+
[[image:cncbender_toolpage_feedadjustpercent.jpg|550px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
 
</table>
 
</table>
 +
 +
==Other Pages==
 +
*Back to [[CNC Bender Technical Notes]]

Latest revision as of 21:00, 15 July 2009

During Feed-Bending it is possible to experience a Feed Axis Fault that is caused by the wrong tool radius values or an incorrect Feed Axis Adjust % value. Both are in the Tool Page.

Quick indicators that should make you suspect that this is the case:

  • The Feed Axis faults especially on large angle bends
  • The Feed Axis does NOT fault when moving the bender through the cycle with no material in the machine.


Diagnostic 1 - Check the Bend Die Radius Values

Possible Problem: The Centerline Radius values do not to match the bend die radii on the bender.

If the radius value is incorrect, then the Feed motion calculated will probably be incorrect. For example, a 90 degree bend angle on a 70 mm radius will move the Feed axis about 110mm. However, if your bender actually uses a 50 mm bend die, then the correct Feed axis motion is about 79mm. The difference of 31mm could easily cause the Feed axis to show a fault condition.

Cncbender toolpage radius.jpg

Diagnostic 2 - Check the Feed Axis % Values

Possible Problem: The Feed Axis Adjust % Value is not set to the proper value in the Tool page.

This value compensates for elongation during Feed-Bending. It is a negative integer value that indicates how much carriage travel to remove from the motion.

Here's an example:

  • At Feed Adjust Percent of 0%, the calculated feed motion for 155.6 degrees of bend is 8.1"

  • However the actual motion of the Feed axis is 7.5"

  • The Feed Adjust Percent is therefore -7.4

Enter that value into the Feed Adjust Percent field and press AutoBuild

Cncbender toolpage feedadjustpercent.jpg

Other Pages

Retrieved from "http://www.advancedtubular.wiki/index.php?title=Feed_Axis_Faults_During_Feed_Bending&oldid=11363"