Difference between revisions of "CNC Bender v11-200900915"
From ATTWiki
(→25px ENHANCED - New Pressure Die Advanced Timer Choice in Processlist Builder) |
|||
| (6 intermediate revisions by one user not shown) | |||
| Line 4: | Line 4: | ||
__NOTOC__ | __NOTOC__ | ||
| − | ===[[image:Check.jpg|25px]] ENHANCED - Pressure Die Advanced Timer Choice in [[Processlist Builder]] === | + | ===[[image:Check.jpg|25px]] ENHANCED - New Pressure Die Advanced Timer Choice in [[Processlist Builder]] === |
The pressure die advance timer choice in the[[ Processlist Builder]] is now dependent on the Pressure Die Assist setup in the Low Level General Dynamic Options list. | The pressure die advance timer choice in the[[ Processlist Builder]] is now dependent on the Pressure Die Assist setup in the Low Level General Dynamic Options list. | ||
| Line 11: | Line 11: | ||
<br><br> | <br><br> | ||
| − | For example, if the PDA Mode is set to Follower / No Prox, then the Processlist Builder will switch to use the new PressureDieAdvanceWithTimer Without PDA command like this: | + | For example, if the PDA Mode is set to '''Follower / No Prox''', then the Processlist Builder will switch to use the new "PressureDieAdvanceWithTimer Without PDA" command in the [[processlist]] like this: |
<font size=2><pre> | <font size=2><pre> | ||
PressureDieAdvanceWithTimer Without PDA = tim2:500, cto:6000 | PressureDieAdvanceWithTimer Without PDA = tim2:500, cto:6000 | ||
</pre></font> | </pre></font> | ||
| + | |||
| + | <br><br> | ||
===[[image:Check.jpg|25px]] ENHANCED - File Path in FRB Page Synchronizes With Low Level Path Settings === | ===[[image:Check.jpg|25px]] ENHANCED - File Path in FRB Page Synchronizes With Low Level Path Settings === | ||
[[image:partpath_lowlevel.jpg]] | [[image:partpath_lowlevel.jpg]] | ||
| − | When the part path in the low level File Paths menu, the path also now automatically changes in the FRB page in Bender Data. | + | When the part path changes in the low level File Paths menu, the path also now automatically changes in the FRB page in Bender Data. |
[[image:partpath_frbmenu.jpg]] | [[image:partpath_frbmenu.jpg]] | ||
| − | |||
| − | |||
===[[image:Check.jpg|25px]] ENHANCED - Processlist Builder Screen Update === | ===[[image:Check.jpg|25px]] ENHANCED - Processlist Builder Screen Update === | ||
| Line 30: | Line 30: | ||
The [[Processlist Builder]] has an updated screen. | The [[Processlist Builder]] has an updated screen. | ||
| − | [[image:processlistbuilder.jpg| | + | [[image:processlistbuilder.jpg|450px]] |
=Other Pages= | =Other Pages= | ||
Latest revision as of 15:27, 15 September 2009
ENHANCED - New Pressure Die Advanced Timer Choice in Processlist Builder
The pressure die advance timer choice in the Processlist Builder is now dependent on the Pressure Die Assist setup in the Low Level General Dynamic Options list.
For example, if the PDA Mode is set to Follower / No Prox, then the Processlist Builder will switch to use the new "PressureDieAdvanceWithTimer Without PDA" command in the processlist like this:
PressureDieAdvanceWithTimer Without PDA = tim2:500, cto:6000
ENHANCED - File Path in FRB Page Synchronizes With Low Level Path Settings
When the part path changes in the low level File Paths menu, the path also now automatically changes in the FRB page in Bender Data.
ENHANCED - Processlist Builder Screen Update
The Processlist Builder has an updated screen.
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See Cycle Hold
- See Hopper Logic
- See Processlist
- See Secondary Processlist
