Difference between revisions of "CNC Bender v11-20090928"
| (11 intermediate revisions by one user not shown) | |||
| Line 4: | Line 4: | ||
__NOTOC__ | __NOTOC__ | ||
| − | ===[[image:Check.jpg|25px]] NEW - Simultaneous Absolute Rotate DURING Final Feed Clearance | + | ===[[image:Check.jpg|25px]] NEW - Simultaneous Absolute Rotate DURING Final Feed Clearance for Faster Cycles === |
This version of CNC Bender uses secondary process lists to set the [[Absolute Rotate]] position in the chuck while the [[Final Feed Clearance]] move is in action.<br><br> | This version of CNC Bender uses secondary process lists to set the [[Absolute Rotate]] position in the chuck while the [[Final Feed Clearance]] move is in action.<br><br> | ||
| Line 10: | Line 10: | ||
This can trim seconds off the part cycle - especially in cases where the [[Absolute Rotate Offset Position]] is far from zero degrees.<br><br> | This can trim seconds off the part cycle - especially in cases where the [[Absolute Rotate Offset Position]] is far from zero degrees.<br><br> | ||
| − | ===[[image:Check.jpg|25px]] NEW - Separate Part Release Mandrel Retract Command === | + | ===[[image:Check.jpg|25px]] NEW - Separate Part Release Mandrel Retract Command for Faster Cycles === |
| − | + | A [[Mandrel Retract Part Release]] command is added to separate it from all other [[Mandrel Retract]]ion commands.<br><br> | |
| + | |||
| + | Since this feature allows CNC Bender to treat the last mandrel retraction separately from the in-bend mandrel retractions, you can increase a pause in the command after the final mandrel retraction while decreasing or eliminating the pauses or prox. switch examinations in the in-bend mandrel retractions - thus shaving cycle time. | ||
<table> | <table> | ||
<tr> | <tr> | ||
| − | <td width=200> | + | <td width=200 cellpadding=10> |
In-Bend Mandrel Retract Command | In-Bend Mandrel Retract Command | ||
</td> | </td> | ||
| Line 41: | Line 43: | ||
*Back to [[CNC Bender Software Updates]] | *Back to [[CNC Bender Software Updates]] | ||
*See [[CNC Bender General Information]] | *See [[CNC Bender General Information]] | ||
| + | *See [[Absolute Rotate]] | ||
| + | *See [[Absolute Rotate Offset Position]] | ||
| + | *See [[Final Feed Clearance]] | ||
| + | *See [[Mandrel Retract]] | ||
| + | *See [[Mandrel Retract Part Release]] | ||
Latest revision as of 06:15, 29 September 2009
NEW - Simultaneous Absolute Rotate DURING Final Feed Clearance for Faster Cycles
This version of CNC Bender uses secondary process lists to set the Absolute Rotate position in the chuck while the Final Feed Clearance move is in action.
This can trim seconds off the part cycle - especially in cases where the Absolute Rotate Offset Position is far from zero degrees.
NEW - Separate Part Release Mandrel Retract Command for Faster Cycles
A Mandrel Retract Part Release command is added to separate it from all other Mandrel Retraction commands.
Since this feature allows CNC Bender to treat the last mandrel retraction separately from the in-bend mandrel retractions, you can increase a pause in the command after the final mandrel retraction while decreasing or eliminating the pauses or prox. switch examinations in the in-bend mandrel retractions - thus shaving cycle time.
|
In-Bend Mandrel Retract Command |
MandrelRetract |
|
New Part Release Mandrel Retract Command |
MandrelRetract_PartRelease |
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Absolute Rotate
- See Absolute Rotate Offset Position
- See Final Feed Clearance
- See Mandrel Retract
- See Mandrel Retract Part Release
