Difference between revisions of "CNC Bender v11-20091007"

From ATTWiki
Jump to: navigation, search
(→‎25px NEW - Spacebar Filter Mode)
(→‎25px NEW - Rotate Reset Mode (Low Level))
 
(34 intermediate revisions by one user not shown)
Line 4: Line 4:
 
__NOTOC__
 
__NOTOC__
  
−
===[[image:Check.jpg|25px]] NEW - Low Level - Rotate Reset Mode ===
+
===[[image:Check.jpg|25px]] NEW - Rotate Reset Mode (Low Level)===
  
 
<table>
 
<table>
 
<tr>
 
<tr>
 
<td width=300>
 
<td width=300>
−
The Rotate Reset Mode controls if the rotate axis is reset to zero between every bend by default.  If you intend to use Absolute Pre-Rotate Enable with multiple parts in the Runlist, and the axis should never reset itself except when homing, then the Rotate Reset mode can be set to DISABLE.
+
By default, the ROTATE AXIS is reset to ZERO degrees between all bends in auto mode.  However, there are customer applications where it makes better sense for the rotate axis angle to never reset rotate position.
 
<br><br>
 
<br><br>
−
The default mode is ENABLED.
+
So now the new Rotate Reset Mode allows you to control if the rotate axis is reset to zero between every bend by default.
 +
<br><br>
 +
If you intend to use Absolute Pre-Rotate Enable (See [[Absolute Rotate]]) with multiple parts in the Runlist, and the axis should never reset itself except when homing, then the Rotate Reset mode can be set to DISABLE.
 +
<br><br>
 +
The default mode is ENABLED - (Reset the rotate axis to zero between bends).
 
</td>
 
</td>
  
 
<td>
 
<td>
−
[[image:benderimage_rotatepart.jpg|300px]]
+
[[image:benderimage_rotatepart.jpg|300px]]<br>
 +
[[image:cncbender_rotateresetmode.jpg|300px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 21: Line 26:
 
</table>
 
</table>
  
 +
===[[image:Check.jpg|25px]] NEW - Bend Axis PID Insert Mode (Low Level) ===
  
−
 
+
<table cellpadding=5>
−
===[[image:Check.jpg|25px]] NEW - Low Level - Bend Axis PID Insert Mode ===
+
−
 
+
−
<table>
+
 
<tr>
 
<tr>
 
<td width=300>
 
<td width=300>
−
The Bend Axis PID Insert Mode controls if the PID COMDEFs are inserted or not into the processlist.<br><br>
+
The new Bend Axis PID Insert Mode controls if the [[PID Tuning COMDEF]]s are inserted into the processlist.
−
The default mode is DISABLED.
+
 
</td>
 
</td>
  
−
<td width=300>
+
<td width=350>
−
PID values control the tuning of the bend axis separately if draw bending or push-bending. This allows for fine tuning for each type of bending.  (Push-bending often needs higher precision than draw bending.)
+
[[image:bendaxis_PID_insertmode.jpg|350px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 39: Line 41:
 
</table>
 
</table>
  
−
===[[image:Check.jpg|25px]] NEW - Spacebar Filter Mode ===
+
===[[image:Check.jpg|25px]] NEW - Spacebar Filter Mode (Low Level) ===
  
 
<table>
 
<table>
 
<tr>
 
<tr>
 
<td width=300>
 
<td width=300>
 +
 
Pressing the spacebar in Windows causes any focused button to "click."  This can cause manual jog moves with the press of the spacebar.  Some users prefer that this Windows feature be disabled for better safety.
 
Pressing the spacebar in Windows causes any focused button to "click."  This can cause manual jog moves with the press of the spacebar.  Some users prefer that this Windows feature be disabled for better safety.
 
<br><br>
 
<br><br>
−
This version of CNC Bender has a new Spacebar Filter Mode in Low Level that, by default, will prevent the "clicking" of any buttons or controls in CNC Bender software.  The exceptions are:
+
[[image:vectorkeyboard.jpg|300px]]
 +
<br><br>
 +
This version of CNC Bender has a new Spacebar Filter Mode in Low Level that, by default, will prevent the "clicking" of any buttons or controls in CNC Bender software using the spacebar.  The exceptions are:
  
 
*When CNC Bender is in the Low Level menu.
 
*When CNC Bender is in the Low Level menu.
Line 60: Line 65:
  
 
<br><br>
 
<br><br>
−
 
−
 
  
 
===[[image:Check.jpg|25px]] NEW - Notes Included in General Section of Reports ===
 
===[[image:Check.jpg|25px]] NEW - Notes Included in General Section of Reports ===
Line 68: Line 71:
 
<tr>
 
<tr>
 
<td width=300>
 
<td width=300>
−
The NOTES data is now included in CNC Bender reports and in the File Load screens.<br><br>
+
Customers have asked us to display the note data from the General Setup in all report.
 +
<br><br>
 +
So now this data is automatically included in any CNC Bender report that displays the General section.
 +
<br><br>
 +
The notes display is included in the Load Part File and Load Tool File menus.
 +
<br><br>
 +
Click on the image to see a closeup.
 
</td>
 
</td>
  
 
<td>
 
<td>
−
[[image:cncbender_notesdata_displayed.jpg|300px]]
+
[[image:cncbender_notesdata_displayed.jpg|400px]]
 
</td>
 
</td>
  

Latest revision as of 20:47, 7 October 2009

Cncbender logo pushbending.png

Operatorstation model.jpg


Check.jpg NEW - Rotate Reset Mode (Low Level)

By default, the ROTATE AXIS is reset to ZERO degrees between all bends in auto mode. However, there are customer applications where it makes better sense for the rotate axis angle to never reset rotate position.

So now the new Rotate Reset Mode allows you to control if the rotate axis is reset to zero between every bend by default.

If you intend to use Absolute Pre-Rotate Enable (See Absolute Rotate) with multiple parts in the Runlist, and the axis should never reset itself except when homing, then the Rotate Reset mode can be set to DISABLE.

The default mode is ENABLED - (Reset the rotate axis to zero between bends).

Benderimage rotatepart.jpg
Cncbender rotateresetmode.jpg

Check.jpg NEW - Bend Axis PID Insert Mode (Low Level)

The new Bend Axis PID Insert Mode controls if the PID Tuning COMDEFs are inserted into the processlist.

Bendaxis PID insertmode.jpg

Check.jpg NEW - Spacebar Filter Mode (Low Level)

Pressing the spacebar in Windows causes any focused button to "click." This can cause manual jog moves with the press of the spacebar. Some users prefer that this Windows feature be disabled for better safety.

Vectorkeyboard.jpg

This version of CNC Bender has a new Spacebar Filter Mode in Low Level that, by default, will prevent the "clicking" of any buttons or controls in CNC Bender software using the spacebar. The exceptions are:

  • When CNC Bender is in the Low Level menu.
  • When the CNC Bender numeric keypad is active.

Operatorstation top.jpg



Check.jpg NEW - Notes Included in General Section of Reports

Customers have asked us to display the note data from the General Setup in all report.

So now this data is automatically included in any CNC Bender report that displays the General section.

The notes display is included in the Load Part File and Load Tool File menus.

Click on the image to see a closeup.

Cncbender notesdata displayed.jpg



Other Pages

Retrieved from "http://www.advancedtubular.wiki/index.php?title=CNC_Bender_v11-20091007&oldid=12170"