Difference between revisions of "CNC Bender v11-20091118"

From ATTWiki
Jump to: navigation, search
(→‎25px ENHANCE - AllDiesToHome Command and AllDiesToHomeWithoutPDA Commands)
(→‎25px ENHANCE - AllDiesToHome Command and AllDiesToHomeWithoutPDA Commands)
Line 72: Line 72:
  
 
<td width=300>
 
<td width=300>
−
# When returning a PDA motion-controlled axis, then AllDiesToHomeWithoutPDA is called immediately after in order to insure  
+
# When returning a PDA motion-controlled axis, then AllDiesToHomeWithoutPDA is called immediately after in order to insure that the pressure die and clamp dies are home before continuing.
−
that the pressure die and clamp dies are home before continuing.
+
−
 
+
 
# When using a FOLLOWER with NO prox, then AllDiesToHomeWithoutPDA is called immediately after in order to insure that the pressure die and clamp dies are home before continuing.
 
# When using a FOLLOWER with NO prox, then AllDiesToHomeWithoutPDA is called immediately after in order to insure that the pressure die and clamp dies are home before continuing.
−
 
 
# When returning a PDA directional valve actuator, then AllDiesToHome is called to be sure the pressure die, clamp die, and Pressure Die Assist die are home before continuing.
 
# When returning a PDA directional valve actuator, then AllDiesToHome is called to be sure the pressure die, clamp die, and Pressure Die Assist die are home before continuing.
−
 
 
# When returning a FOLLOWR with a prox switch, then AllDiesToHome is called to be sure the pressure die, clamp die, and Pressure Die Assist die are home before continuing.
 
# When returning a FOLLOWR with a prox switch, then AllDiesToHome is called to be sure the pressure die, clamp die, and Pressure Die Assist die are home before continuing.
  

Revision as of 12:58, 19 November 2009

Cncbender logo pushbending.png

Type of Upgrade: FASTER BENDING

The changes in this version are minor debugs to the November 4, 2009 version of CNC Bender - Speed optimizations. (See CNC Bender v11-20091104 and CNC Bender v11-20090518)

Operatorstation model.jpg



Check.jpg REPAIR- Final Bend Simultaneous Motion

  • If the final Bend Return Step Point is ZERO, then the standard "BendAbsolute" command is now called correctly without generating errors during AutoBuild.

  • This switches the immediate move "Bend Absolute" off - which makes CNC Bender wait for the bend arm to completely return home before moving to the next step in the process.


Bendarm blur vb150.jpg

BendReturnStepPoint FinalRow.jpg



Check.jpg REPAIR- Time-Out Value for Bend Arm Return

  • The bend arm return timeout value was accidentally set to the Run Buttons timeout in the previous version.

  • This has been resolved so that the axis timeout value is once again used.




Check.jpg ENHANCE - AllDiesToHome Command and AllDiesToHomeWithoutPDA Commands

  • Both of these commands can now be named in the General Dynamic Option List in Low Level.
  1. When returning a PDA motion-controlled axis, then AllDiesToHomeWithoutPDA is called immediately after in order to insure that the pressure die and clamp dies are home before continuing.
  2. When using a FOLLOWER with NO prox, then AllDiesToHomeWithoutPDA is called immediately after in order to insure that the pressure die and clamp dies are home before continuing.
  3. When returning a PDA directional valve actuator, then AllDiesToHome is called to be sure the pressure die, clamp die, and Pressure Die Assist die are home before continuing.
  4. When returning a FOLLOWR with a prox switch, then AllDiesToHome is called to be sure the pressure die, clamp die, and Pressure Die Assist die are home before continuing.



Other Pages

Retrieved from "http://www.advancedtubular.wiki/index.php?title=CNC_Bender_v11-20091118&oldid=12479"