Difference between revisions of "CNC Bender v12-20100105"

From ATTWiki
Jump to: navigation, search
(→‎25px NEW - TEACH MODE)
(→‎25px NEW - TEACH MODE and CUSTOM COMMANDS)
Line 67: Line 67:
 
<br><br>
 
<br><br>
  
−
===[[image:Check.jpg|25px]] NEW - TEACH MODE and CUSTOM COMMANDS===
+
===[[image:Check.jpg|25px]] NEW - CUSTOM COMMANDS===
 
<table>
 
<table>
 
<tr valign=middle>
 
<tr valign=middle>
 
<td width=300>
 
<td width=300>
−
* CNC Bender can now learn from you during setup. <b>Teach the bender any motion for difficult transitions between bends</b><br><br>
+
* Custom Commands store the moves learned during Teach Mode<br><br>
−
* The learned moves are held in objects called [[Custom Commands]].<br><br>
+
* A ''single'' Custom Command can contain any number of simultaneous [[Jog Motion]]s. In a SINGLE Custom Command, you could teach the bender how to move the...
−
* '''PreBend''' allows for 10 Custom Commands.  They run immediately after you press the run buttons.<br><br>
+
−
* Each '''BEND''' can be followed by up to 10 Custom Commands.<br><br>
+
−
* Control extra moves in '''PostBend''' using the final bend's Custom Commands.<br><br>
+
−
* Each Custom Command can contain any number of simultaneous [[Jog Motion]]s. In a SINGLE Custom Command, you could teach the bender how to move the...
+
 
** FEED (carriage)
 
** FEED (carriage)
 
** while ROTATING
 
** while ROTATING
Line 85: Line 81:
 
** while activating the KICKER
 
** while activating the KICKER
 
** while doing anything else you can make move on the bender<br><br>
 
** while doing anything else you can make move on the bender<br><br>
−
* So Custom Commands can control all axes and actuators around the bender including directional valves - clamp, pressure die, kickers, grippers, mandrel, mist, machine lube - ANY ACTUATOR.<br><br>
 
 
* Custom Commands can be MANUALLY entered and edited.  You can enter Custom Commands ''without'' [[Teach Mode]].<br><br>
 
* Custom Commands can be MANUALLY entered and edited.  You can enter Custom Commands ''without'' [[Teach Mode]].<br><br>
 
* Custom Commands can be edited even ''after'' they were learned during Teach Mode.<br><br>
 
* Custom Commands can be edited even ''after'' they were learned during Teach Mode.<br><br>
Line 91: Line 86:
  
 
<td>
 
<td>
−
[[image:cncv12_runpage_teachbutton.jpg|300px|thumb|New TEACH speed button in the Control Mode bar]]
+
[[image:cncb12frb_customcommands_button.jpg|300px|thumb|Edit custom commands in the FRB page]]
−
[[image:v12teachmodemenu.jpg|300px|thumb|Teach Mode activates after a Teach Mode Section was encountered during bending]]<br><br>
+
 
[[image:v12customcommandeditor_teachmode.jpg|300px|thumb|Custom Command Editor during Teach Mode]]<br><br>
 
[[image:v12customcommandeditor_teachmode.jpg|300px|thumb|Custom Command Editor during Teach Mode]]<br><br>
  

Revision as of 16:35, 18 January 2010

Cncbender logo.jpg

Type of Upgrade: MAJOR VERSION CHANGE with Teach Mode

The changes in this version take CNC Bender to the next step in setup power: TEACH your bender how to solve problems.

The new v12 main menu in CNC Bender ProControl

Contents



Check.jpg NEW - TEACH MODE

New TEACH speed button in the Control Mode bar


  • CNC Bender can now learn from you during setup. Teach the bender any motion for difficult transitions between bends

  • The learned moves are held in objects called Custom Commands (see more below).

  • PreBend allows for 10 Custom Commands. They run immediately after you press the run buttons.

  • Each BEND can be followed by up to 10 Custom Commands.

  • Control extra moves in PostBend using the final bend's Custom Commands.
Teach Mode activates after a Teach Mode Section was encountered during bending


Custom Command Editor during Teach Mode
Cncb12frb customcommands button.jpg


FRB menu with Edit Custom buttons after each bend




Check.jpg NEW - CUSTOM COMMANDS

  • Custom Commands store the moves learned during Teach Mode

  • A single Custom Command can contain any number of simultaneous Jog Motions. In a SINGLE Custom Command, you could teach the bender how to move the...
    • FEED (carriage)
    • while ROTATING
    • while shifting the VERTICAL RADIUS
    • while shifting the HORIZONTAL RADIUS
    • while returning the BEND ARM
    • while pulling the MANDREL
    • while activating the KICKER
    • while doing anything else you can make move on the bender

  • Custom Commands can be MANUALLY entered and edited. You can enter Custom Commands without Teach Mode.

  • Custom Commands can be edited even after they were learned during Teach Mode.
Edit custom commands in the FRB page
Custom Command Editor during Teach Mode
Cncb12frb customcommands button.jpg


FRB menu with Edit Custom buttons after each bend




Other Pages

Retrieved from "http://www.advancedtubular.wiki/index.php?title=CNC_Bender_v12-20100105&oldid=13229"