Difference between revisions of "CNC Bender v12-20100316"
From ATTWiki
| (8 intermediate revisions by one user not shown) | |||
| Line 18: | Line 18: | ||
</td> | </td> | ||
<td> | <td> | ||
| − | [[image:v12mainmenu.jpg| | + | [[image:v12mainmenu.jpg|200px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 32: | Line 32: | ||
<br><br> | <br><br> | ||
</td> | </td> | ||
| − | <td> | + | <td width=400> |
[[image:FeedSpeedPercentageAdjustmentOption.jpg|400px]] | [[image:FeedSpeedPercentageAdjustmentOption.jpg|400px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
| − | <tr><td>Value Type:</td><td>The value is entered as a floating point percentage.</td></tr> | + | <tr><td>'''Value Type:'''</td><td>The value is entered as a floating point percentage.</td></tr> |
| − | <tr><td>+ or -:</td><td>The value can be positive or negative.</td></tr> | + | <tr><td>'''+ or -:'''</td><td>The value can be positive or negative.</td></tr> |
| − | <tr><td>Impact of Negative Values:</td><td>Negative values slow the calculated speed of the Feed axis | + | <tr><td>'''Impact of Negative Values:'''</td><td>Negative values slow the calculated speed of the Feed axis when pushing behind a draw bend</td></tr> |
| − | <tr><td>Example +:</td><td>A value of +100 would double the speed of the Feed axis during draw bending.</td></tr> | + | <tr><td>'''Example +:'''</td><td>A value of +100 would double the speed of the Feed axis during draw bending.</td></tr> |
| − | <tr><td>Example -:</td><td>A value of -100 would set the speed at 0 for the Feed axis during draw bending. | + | <tr><td>'''Example -:'''</td><td>A value of -100 would set the speed at 0 for the Feed axis during draw bending.</td></tr> |
| − | + | ||
| − | + | ||
| − | + | ||
<tr valign=top> | <tr valign=top> | ||
<td> | <td> | ||
| + | <br><br> | ||
The table at the right shows an example of a -10% change in the processlist: | The table at the right shows an example of a -10% change in the processlist: | ||
</td> | </td> | ||
<td> | <td> | ||
| + | <br><br> | ||
See vel0 calculated at 100%:<br> | See vel0 calculated at 100%:<br> | ||
[[image:processlist_feedspeedadjustbefore.jpg|400px]]<br><br> | [[image:processlist_feedspeedadjustbefore.jpg|400px]]<br><br> | ||
Latest revision as of 13:09, 16 March 2010
|
|
|
Contents |
NEW - Feed Speed Percentage Adjustment for Feed Bend Mode
|
This new bend option allows you to fine-tune the calculated feed speed during Feed Bending.
|
|
| Value Type: | The value is entered as a floating point percentage. |
| + or -: | The value can be positive or negative. |
| Impact of Negative Values: | Negative values slow the calculated speed of the Feed axis when pushing behind a draw bend |
| Example +: | A value of +100 would double the speed of the Feed axis during draw bending. |
| Example -: | A value of -100 would set the speed at 0 for the Feed axis during draw bending. |
|
|
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
