Difference between revisions of "CNC Bender v12-20100611"
From ATTWiki
| (24 intermediate revisions by one user not shown) | |||
| Line 2: | Line 2: | ||
<tr> | <tr> | ||
<td width=300> | <td width=300> | ||
| − | [[image:cncv12procontrol_withteachmode.jpg|300px]] | + | [[image:cncv12procontrol_withteachmode.jpg|300px]]<br> |
| − | <br> | + | [[image:teachmodejoystick.jpg|400px]] |
| − | + | ||
| − | + | ||
</td> | </td> | ||
<td> | <td> | ||
| − | |||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | + | __NOTOC__ | |
| − | ===[[image:Check.jpg|25px]] NEW - CNC Bender Jog with Joystick or Pendant=== | + | ===[[image:Check.jpg|25px]] NEW - CNC Bender Direct-Axis Jog with Joystick or Pendant=== |
<table> | <table> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
CNC Bender can now respond to a joystick or pendant buttons when direct-axis jogging. | CNC Bender can now respond to a joystick or pendant buttons when direct-axis jogging. | ||
| − | < | + | <br><br> |
| − | < | + | Direct axis jogs using external devices is active in the MANUAL and TEACH MODE pages. |
| − | + | <br><br> | |
| − | < | + | In the MANUAL page, the joystick or pendant is used only when the Direct Axis jog button is activated. |
| − | < | + | <br><br> |
| + | In the CUSTOM COMMAND EDITOR page, the joystick or pendant is used only when the TEACH button is activated.<br><br> | ||
| − | + | In the CUSTOM COMMAND EDITOR in TEACH mode, the joystick and [[SMT Teach Pendant]] can control both SERVO and DIRECTIONAL-VALVE actuators. In other words - they can control all actuators. | |
| − | + | ||
</td> | </td> | ||
<td> | <td> | ||
| + | [[image:joystick.jpg|250px]]<br> | ||
| + | [[image:pendant1.jpg|250px|thumb|left|SMT Teach Pendant]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
| − | |||
| − | |||
| − | |||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | |||
| − | |||
</td> | </td> | ||
<td> | <td> | ||
</td> | </td> | ||
</tr> | </tr> | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
</table> | </table> | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] NEW- Setup Options for Direct Axis Jog from INPUTS=== |
<table> | <table> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | + | The low level general options list contains three new options:<br><br> | |
| − | < | + | |
| − | < | + | |
| − | + | ||
| − | + | ||
| − | + | * ENABLE | |
| − | + | * JOG+ Input Name | |
| − | < | + | * JOG- Input Name |
| − | < | + | <br><br> |
| − | < | + | If this feature is enabled, then the input names are used to lookup the input points in the CIO dictionary.<br><br> |
| − | < | + | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
</td> | </td> | ||
<td> | <td> | ||
| Line 89: | Line 62: | ||
<td width=300> | <td width=300> | ||
</td> | </td> | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
<td> | <td> | ||
</td> | </td> | ||
Latest revision as of 02:56, 4 November 2010
|
|
NEW - CNC Bender Direct-Axis Jog with Joystick or Pendant
|
CNC Bender can now respond to a joystick or pendant buttons when direct-axis jogging.
In the CUSTOM COMMAND EDITOR in TEACH mode, the joystick and SMT Teach Pendant can control both SERVO and DIRECTIONAL-VALVE actuators. In other words - they can control all actuators. |
 |
NEW- Setup Options for Direct Axis Jog from INPUTS
|
The low level general options list contains three new options:
|
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
