Difference between revisions of "VTube-LASER v1.59"
From ATTWiki
| (10 intermediate revisions by one user not shown) | |||
| Line 63: | Line 63: | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] ENHANCED- Linear Units Now Set By Single Large Button === |
<table> | <table> | ||
<tr> | <tr> | ||
<td width=200> | <td width=200> | ||
| − | In previous versions, | + | In previous versions, the linear units radio buttons were not reliable in setting the proper state. |
<br><br> | <br><br> | ||
| − | This | + | Plus they were too small to easily press. |
| + | <br><br> | ||
| + | This version removes these radio buttons and uses an large button with either an M or an I that toggles the state. | ||
| + | <br><br> | ||
| + | These buttons can also be localized. The M and I can be changed to other Unicode characters for other languages.</td> | ||
<td> | <td> | ||
| + | Old Interface: | ||
| + | <br> | ||
[[image:vtube_laser_linear_units.jpg]] | [[image:vtube_laser_linear_units.jpg]] | ||
| + | <br> | ||
| + | New Interface: | ||
| + | <br> | ||
| + | [[image:vtube_laser_linear_units_button_millimeter.jpg]] | ||
| + | <br> | ||
| + | [[image:vtube_laser_linear_units_button_inch.jpg]] | ||
| + | <br> | ||
</td> | </td> | ||
</tr> | </tr> | ||
| Line 77: | Line 90: | ||
<br><br> | <br><br> | ||
| − | |||
===[[image:Check.jpg|25px]] REPAIR- Laser Active Initialization === | ===[[image:Check.jpg|25px]] REPAIR- Laser Active Initialization === | ||
| Line 87: | Line 99: | ||
<td> | <td> | ||
[[image:vtube_laser_measuresetup.jpg]] | [[image:vtube_laser_measuresetup.jpg]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | <br><br> | ||
| + | |||
| + | |||
| + | |||
| + | ===[[image:Check.jpg|25px]] Other Changes === | ||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=300> | ||
| + | * The report window now requires an operator to close the window before using any other part of VTube. | ||
| + | <br> | ||
| + | * The print preview window buttons are re-arranged so that they are larger and easier to press. The Print button is moved to the right side of the window. | ||
| + | <br> | ||
| + | * If VTube changes from cylinder fit to centerline projection mode during a measurement, VTube will now always consider the measure a cylinder fit failure. | ||
| + | |||
| + | </td> | ||
| + | |||
| + | <td> | ||
</td> | </td> | ||
</tr> | </tr> | ||
| Line 111: | Line 144: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=500> | <td width=500> | ||
| − | * | + | * Better end-scan qualification. Detect and remove outlier points. |
| + | * See [[VTube-LASER v1.6]] | ||
| + | </td> | ||
| + | |||
<td width=300> | <td width=300> | ||
</td> | </td> | ||
Latest revision as of 22:13, 21 February 2011
|
Revision 1.59Back to VTube-LASER |
|
NEW: Help Reference for LASER Mode
|
Now VTube-LASER has its own help reference. |
|
REPAIR: Mix ball probe and laser measurement
|
Using ball probe measurements on the end scans and and laser measurements in the cylinder straights now offsets the ball radius point properly in every case. |
|
ENHANCEMENT- Part Name is Used as Filename When Part Name Changes
|
In previous versions, the part name was used as the filename only if the previous filename was empty.
|
|
ENHANCED- Linear Units Now Set By Single Large Button
|
In previous versions, the linear units radio buttons were not reliable in setting the proper state.
|
Old Interface:
|
REPAIR- Laser Active Initialization
|
In previous versions, VTube required the operator to enter Measure Setup at least one time when coming into Laser Mode in order to setup the Laser active mode. |
|
Other Changes
|
Changes to VTube-STEP
|
Issues with this version fixed in next version
|
Other Pages
- Back to VTube-LASER
