Difference between revisions of "VTube-LASER v1.59"

From ATTWiki
Jump to: navigation, search
(→‎25px REPAIR- Laser Active Initialization)
(→‎25px Issues with this version fixed in next version)
 
(4 intermediate revisions by one user not shown)
Line 112: Line 112:
 
<td width=300>
 
<td width=300>
 
* The report window now requires an operator to close the window before using any other part of VTube.
 
* The report window now requires an operator to close the window before using any other part of VTube.
 +
<br>
 
* The print preview window buttons are re-arranged so that they are larger and easier to press.  The Print button is moved to the right side of the window.
 
* The print preview window buttons are re-arranged so that they are larger and easier to press.  The Print button is moved to the right side of the window.
 +
<br>
 +
* If VTube changes from cylinder fit to centerline projection mode during a measurement, VTube will now always consider the measure a cylinder fit failure.
 +
 
</td>
 
</td>
  
Line 140: Line 144:
 
<tr valign=top>
 
<tr valign=top>
 
<td width=500>
 
<td width=500>
−
* No known issues</td>
+
* Better end-scan qualification.  Detect and remove outlier points.
 +
* See [[VTube-LASER v1.6]]
 +
</td>
 +
 
 
<td width=300>
 
<td width=300>
 
</td>
 
</td>

Latest revision as of 22:13, 21 February 2011

Vtube-laser logo.jpg

Revision 1.59

Back to VTube-LASER

Vtube-laser 1 57.jpg



Check.jpg NEW: Help Reference for LASER Mode

Now VTube-LASER has its own help reference.

Vtube-laser help button.jpg

Vtube-laser help reference.jpg



Check.jpg REPAIR: Mix ball probe and laser measurement

Using ball probe measurements on the end scans and and laser measurements in the cylinder straights now offsets the ball radius point properly in every case.

Vtube-laser ballprobe endscan.jpg




Check.jpg ENHANCEMENT- Part Name is Used as Filename When Part Name Changes

In previous versions, the part name was used as the filename only if the previous filename was empty.

Now - when the part name changes, the part name is used as the initial filename in the Save dialog.

Vtube savefile partname.jpg




Check.jpg ENHANCED- Linear Units Now Set By Single Large Button

In previous versions, the linear units radio buttons were not reliable in setting the proper state.

Plus they were too small to easily press.

This version removes these radio buttons and uses an large button with either an M or an I that toggles the state.

These buttons can also be localized. The M and I can be changed to other Unicode characters for other languages.

Old Interface:
Vtube laser linear units.jpg
New Interface:
Vtube laser linear units button millimeter.jpg
Vtube laser linear units button inch.jpg



Check.jpg REPAIR- Laser Active Initialization

In previous versions, VTube required the operator to enter Measure Setup at least one time when coming into Laser Mode in order to setup the Laser active mode.

This has been corrected in this version. It is no longer necessary to enter measure setup if you know the setup is correct.

Vtube laser measuresetup.jpg




Check.jpg Other Changes

  • The report window now requires an operator to close the window before using any other part of VTube.


  • The print preview window buttons are re-arranged so that they are larger and easier to press. The Print button is moved to the right side of the window.


  • If VTube changes from cylinder fit to centerline projection mode during a measurement, VTube will now always consider the measure a cylinder fit failure.



Check.jpg Changes to VTube-STEP



Check.jpg Issues with this version fixed in next version

  • Better end-scan qualification. Detect and remove outlier points.
  • See VTube-LASER v1.6

Other Pages

Retrieved from "http://www.advancedtubular.wiki/index.php?title=VTube-LASER_v1.59&oldid=16066"