Difference between revisions of "VTube-LASER v1.58"

From ATTWiki
Jump to: navigation, search
(→‎25px ENHANCED: Springback Compensation for Corrections)
(→‎25px Issues with this version fixed in next version)
 
(11 intermediate revisions by one user not shown)
Line 24: Line 24:
 
<br><br>
 
<br><br>
 
[[image:vtube-laser_1_58_constructtube_control.jpg|200px]]
 
[[image:vtube-laser_1_58_constructtube_control.jpg|200px]]
−
<br><br>
 
−
The new Construct Tube Control (shown above) allows you to point to any location in space to designate an end point or an intersection point.  It also allows you to increase the number of straights/points on-the-fly.  This allows operators to change the number of points at any time during the measurement process.
 
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
 
[[image:vtube-laser_1_58_constructtube_closeup.jpg|300px]]<br><br>
 
[[image:vtube-laser_1_58_constructtube_closeup.jpg|300px]]<br><br>
 
[[image:vtube-laser_1_58_constructtube.jpg|300px]]
 
[[image:vtube-laser_1_58_constructtube.jpg|300px]]
 +
</td>
 +
</tr>
 +
</table>
 +
<table cellpadding=10>
 +
<tr valign=top>
 +
<td width=500>
 +
The new Construct Tube Control (shown above) allows you to point to any location in space to designate an end point or an intersection point.  It also allows you to increase the number of straights/points on-the-fly.  This allows operators to change the number of points at any time during the measurement process.
 +
</td>
 +
<td width=300>
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 98: Line 105:
 
<br><br>
 
<br><br>
  
−
 
+
===[[image:Check.jpg|25px]] Issues with this version fixed in next version===
−
 
+
−
===[[image:Check.jpg|25px]] NEW: Transfer Master LRA to Setup LRA with Springback Compensation  ===
+
  
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
−
<td width=200>
+
<td width=500>
−
When transferring data from the VTube MASTER LRA to the BENDER SETUP LRA, automatic springback compensation is automatically applied if the springback values are non-zero.</td>
+
* When using tactile end-measure and laser straight measure in the same tube, the tactile measurements would never be offset by the ball radius. Don't mix tactile and laser measurements in this version or previous versions of VTube.
−
<td width=300>
+
* See [[VTube-LASER v1.59]]
−
[[image:vtube-laser_1_57_bendersetup_master2setup_autospringback.jpg|300px]].
+
−
</td>
+
−
</tr>
+
−
</table>
+
−
 
+
−
<br><br>
+
−
 
+
−
===[[image:Check.jpg|25px]] NEW: Part Name in Toolbar  ===
+
−
[[image:vtube-laser_1_57_toolbar_filename.jpg|500px]]
+
−
<table cellpadding=10>
+
−
<tr valign=top>
+
−
<td width=200>
+
−
The current part name is now displayed in the toolbar below the VTube-LASER logo.
+
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
Line 125: Line 117:
 
</tr>
 
</tr>
 
</table>
 
</table>
−
<br><br>
 
−
 
−
===[[image:Check.jpg|25px]] NEW- Springback Values Transfer from Overbend  ===
 
−
<table cellpadding=10>
 
−
<tr valign=top>
 
−
<td width=200>
 
−
VTube-LASER can now receive springback data from Overbend with the press of a single button in the Overbend Calculator.<br><br>
 
−
</td>
 
−
<td>
 
−
[[image:vtube-laser_1_57_overbend_sendvaluestovtube.jpg|300px]]<br><br>
 
−
</td>
 
−
</tr>
 
−
</table>
 
−
[[image:vtube-laser_1_57_overbend_transfer.jpg|500px]]
 
−
<br><br>
 
−
 
−
===[[image:Check.jpg|25px]] ENHANCED - Other Changes  ===
 
−
 
−
<table cellpadding=10>
 
−
<tr valign=top>
 
−
<td width=200>
 
−
* Added high precision angular decimal places value in System Option/Math
 
−
<br><br>
 
−
* Made Comments to display after the file has loaded and the graphic is displayed on the screen.
 
−
<br><br>
 
−
* The BEST FIT alignment procedure is fine tuned to run about 6 times faster than in previous versions with no loss of accuracy.
 
−
<br><br>
 
−
* Improvements/fixes to Supravision RECALL procedures.
 
−
 
−
[[image:vtube-laser_1_57_benderrecall.jpg|200px]]<br><br>
 
−
</td>
 
−
<td>
 
−
[[image:vtube-laser_1_57_highprec_angledecimalplaces.jpg|300px]]<br><br>
 
−
[[image:vtube-laser_1_57_partcomments.jpg|300px]]<br><br>
 
−
[[image:vtube-laser_1_57_bestfit_image.jpg|300px]]<br><br>
 
−
 
−
</td>
 
−
</tr>
 
−
</table>
 
−
 
−
 
−
<br><br>
 
  
 
=Other Pages=
 
=Other Pages=
 
*Back to [[VTube-LASER]]
 
*Back to [[VTube-LASER]]

Latest revision as of 22:14, 21 February 2011

Vtube-laser logo.jpg

Revision 1.58

Back to VTube-LASER

Vtube-laser 1 58.jpg


Check.jpg NEW: Construct Tube in 3D Space

Tube shapes can now be constructed by pointing the arm ball probe to the end points and intersection points.

This feature allows you to route a tube in 3D space.

The feature is used by our customers to construct tube routes in a vehicle's engine compartment or under the car on a lift.

Vtube-laser 1 58 constructtube control.jpg

Vtube-laser 1 58 constructtube closeup.jpg

Vtube-laser 1 58 constructtube.jpg

The new Construct Tube Control (shown above) allows you to point to any location in space to designate an end point or an intersection point. It also allows you to increase the number of straights/points on-the-fly. This allows operators to change the number of points at any time during the measurement process.



Check.jpg ENHANCED: Measure Tube Control - Decrease / Increase Button

Operators can now increase or decrease the number of straights to measure in the tube on-the-fly if necessary. The new Decrease/Increase buttons are inserted on the control.

The control also shows the total number of straights being measured. So now the control will read, for example "Straight 1 of 5" - rather than just "Straight 1."

Vtube-laser 1 58 measuretube control.jpg



Check.jpg NEW: Show SCANNED or CALCULATED Graphic Data Any Time

VTube now allows operators to show or hide the orange scanned points or the large orange calculated end and intersection points at any time.

Vtube-laser 1 58 scanned calculated display.jpg.



Check.jpg NEW: Auto Display SCANNED and CALCULATED

Vtube-laser 1 58 autodisplay scanned calculated.jpg

The Draw Options feature is new to Measure Setup. You can select these two options if you want the SCANNED or the CALCULATED data to display or not during measurement. If both features are unchecked, then the tube measurement shows now realtime graphics data during measurement - like other measurement software.



Check.jpg ENHANCED: Highlighted Cylinder Fit Box During High Error

Vtube-laser 1 58 cylinderfit highlight.jpg

The cylinder fit box highlights to YELLOW when it encounters a measurement in the tube that is outside the preprogrammed tolerance for cylinder fit.



Check.jpg Issues with this version fixed in next version

  • When using tactile end-measure and laser straight measure in the same tube, the tactile measurements would never be offset by the ball radius. Don't mix tactile and laser measurements in this version or previous versions of VTube.
  • See VTube-LASER v1.59

Other Pages

Retrieved from "http://www.advancedtubular.wiki/index.php?title=VTube-LASER_v1.58&oldid=16067"