Difference between revisions of "VTube-LASER v1.65"
(→Revision 1.65) |
|||
| (11 intermediate revisions by one user not shown) | |||
| Line 7: | Line 7: | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | [[image:vtube- | + | [[image:vtube-laser_screen_1_65.jpg|300px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 15: | Line 15: | ||
===[[image:Check.jpg|25px]] NEW: Radius Correction for Push-Bending=== | ===[[image:Check.jpg|25px]] NEW: Radius Correction for Push-Bending=== | ||
| − | [[image:vtube-laser_1_65_radiuscorrection.jpg| | + | [[image:vtube-laser_1_65_radiuscorrection.jpg|425px]]<br><br> |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
| Line 23: | Line 23: | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | [[image:vtube-laser_1_65_radiusstripescan_sendradius.jpg| | + | [[image:vtube-laser_1_65_radiusstripescan_sendradius.jpg|200px]] |
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| + | |||
<br><br> | <br><br> | ||
| Line 36: | Line 37: | ||
<td width=200> | <td width=200> | ||
The Bender Setup window has a new easier-to-view color scheme.<br><br> | The Bender Setup window has a new easier-to-view color scheme.<br><br> | ||
| + | * ORANGE Columns are NEW ADJUSTED data to be sent out to the bender.<br> | ||
| + | * BLUE Columns contain the current bender setup before adjustment. | ||
| + | |||
The bend setup grid has a new column for inverting rotations that are sent out to the bender. This allows for sending the rotation the opposite direction - then remembering the inversion for next time the project is run. | The bend setup grid has a new column for inverting rotations that are sent out to the bender. This allows for sending the rotation the opposite direction - then remembering the inversion for next time the project is run. | ||
</td> | </td> | ||
| Line 72: | Line 76: | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | [[image:vtube-laser_1_65_benderpluscorrections.jpg| | + | [[image:vtube-laser_1_65_benderpluscorrections.jpg|500px]] |
<br><br> | <br><br> | ||
| Line 97: | Line 101: | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | |||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| + | [[image:vtube-laser_1_65_radiusstripescansuselaser.jpg|300px]] | ||
<br><br> | <br><br> | ||
| − | |||
===[[image:Check.jpg|25px]] ENHANCED: Measure Setup - Scan Rate Grid=== | ===[[image:Check.jpg|25px]] ENHANCED: Measure Setup - Scan Rate Grid=== | ||
| Line 112: | Line 115: | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | |||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| + | [[image:vtube-laser_1_65_radiusstripescansscansrate.jpg|300px]] | ||
<br><br> | <br><br> | ||
| − | |||
| − | |||
===[[image:Check.jpg|25px]] Other Changes=== | ===[[image:Check.jpg|25px]] Other Changes=== | ||
Latest revision as of 17:24, 19 May 2011
|
Revision 1.65Back to VTube-LASER |
|
NEW: Radius Correction for Push-Bending
|
The radius correction menu allows VTube-LASER to correct push-bends on Unison Limited benders. |
|
NEW: Bender Setup Changes
|
The Bender Setup window has a new easier-to-view color scheme.
The bend setup grid has a new column for inverting rotations that are sent out to the bender. This allows for sending the rotation the opposite direction - then remembering the inversion for next time the project is run. |
|
ENHANCED: New Torus-fit Engine for Radius Stripe Scanning
|
The new radius stripe scanning method is more accurate as of this version of VTube due to a new torus-fit engine included in VTube.
|
|
NEW: Bender Data + Corrections Data Chart in Reports
|
A new bender chart was added to the report template to include the bender data + corrections chart |
ENHANCED: Report Preview Menu
|
The Report Preview menu now allows you to change the printer and the paper orientation before printing. |
ENHANCED: Measure Setup - Laser Probe Grid
|
The Laser probe grid now has a separate checkbox for automatically enabling either laser or tactile measuring for radius stripe scans. |
ENHANCED: Measure Setup - Scan Rate Grid
|
The Scan Rate grid now has a separate controls for radius stripe scans. |
Other Changes
|
Issues with this version fixed in newer versions
|
Other Pages
- Back to VTube-LASER
|
VTube-LASER Training Video - How to perform effective end scans. |
|
