Difference between revisions of "CNC Bender v12-20111101"
| (3 intermediate revisions by one user not shown) | |||
| Line 13: | Line 13: | ||
</table> | </table> | ||
__NOTOC__ | __NOTOC__ | ||
| − | ===[[image:Check.jpg|25px]] NEW - Pulse Enable At Halt in Axis List Setup === | + | ===[[image:Check.jpg|25px]] NEW - Feed Boost Features === |
| + | |||
| + | <table cellpadding=10> | ||
| + | <tr valign=top> | ||
| + | <td width=400> | ||
| + | CNC Bender now supports Feed Boost cylinders.<br><br> | ||
| + | |||
| + | The first style of Feed Boosting was to a Hines 800 millimeter bender with boost cylinder that pushes a boost bar connected with a pin that shoots into the bar during bending.<br><br> | ||
| + | |||
| + | The second style was an Eagle with split carriage boosting using a rear cylinder and elevator brake. | ||
| + | |||
| + | </td> | ||
| + | |||
| + | <td width=300> | ||
| + | </td> | ||
| + | |||
| + | |||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] NEW - "Pulse Enable At Halt" in Axis List Setup === | ||
<table cellpadding=10> | <table cellpadding=10> | ||
| Line 25: | Line 45: | ||
</td> | </td> | ||
| − | <td> | + | <td width=300> |
The default value is "1" which means "true" or "enabled." Use 0 to switch this feature off. | The default value is "1" which means "true" or "enabled." Use 0 to switch this feature off. | ||
</td> | </td> | ||
| Line 32: | Line 52: | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | |||
===[[image:Check.jpg|25px]] NEW - "Enable Only To Move" in Axis List Setup === | ===[[image:Check.jpg|25px]] NEW - "Enable Only To Move" in Axis List Setup === | ||
| Line 45: | Line 64: | ||
</td> | </td> | ||
| − | <td> | + | <td width=300> |
The default value is "0" which means "disabled." Use 1 to switch this feature on. | The default value is "0" which means "disabled." Use 1 to switch this feature on. | ||
</td> | </td> | ||
Latest revision as of 01:38, 4 November 2011
v12-20111101
|
|
NEW - Feed Boost Features
|
CNC Bender now supports Feed Boost cylinders. The first style of Feed Boosting was to a Hines 800 millimeter bender with boost cylinder that pushes a boost bar connected with a pin that shoots into the bar during bending. The second style was an Eagle with split carriage boosting using a rear cylinder and elevator brake. |
NEW - "Pulse Enable At Halt" in Axis List Setup
|
"Pulse Enable At Halt=" is a new parameter in the axis list configuration. This allows you to setup CNC Bender to always pulse the enable of an axis during the HALT command. This makes the axis super safe because it always clears all following error. |
The default value is "1" which means "true" or "enabled." Use 0 to switch this feature off. |
NEW - "Enable Only To Move" in Axis List Setup
|
"Enable Only To Move=" is a new parameter in the axis list configuration. This allows you to setup CNC Bender to enable axes only when in motion. |
The default value is "0" which means "disabled." Use 1 to switch this feature on. |
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
