|
|
| Line 46: |
Line 46: |
| | </table> | | </table> |
| | | | |
| − | ===[[image:Check.jpg|25px]] ENHANCED - PDA Motion in Test Bend ===
| |
| | | | |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=400>
| |
| − | * The PDA gearing is now properly set if the RVG (Realtime Variable Gearing) feature is off or on. If RVG is ON, then the gearing PDA electronic gearing is set based on the bend angle.<br><br>
| |
| − | * The PDA returns home when the operator presses All Dies Home.<br><br>
| |
| − | </td>
| |
| − |
| |
| − | <td width=300>
| |
| − | </td>
| |
| − |
| |
| − |
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | ===[[image:Check.jpg|25px]] REPAIR - Tube Support During Home ===
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=400>
| |
| − | * The Tube Support now stays DOWN during homing when the tube support UP enable feature is disabled.<br>
| |
| − | </td>
| |
| − |
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | ===[[image:Check.jpg|25px]] New - [AXIS ENABLE AT ALL TIMES] Internal Command ===
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=400>
| |
| − | * This command is used by the process list builder to enable the Feed axis even when the axis list is setup to only enable when moving. This ensures that the Feed axes with low gearbox ratios stay in position when loading the tube.
| |
| − | </td>
| |
| − |
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | ===[[image:Check.jpg|25px]] New - [AXIS ENABLE ONLY TO MOVE] Internal Command ===
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=400>
| |
| − | * This command is used by the process list builder to allow the Feed axis to disable when not moving.<br>
| |
| − | </td>
| |
| − |
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − |
| |
| − | ===[[image:Check.jpg|25px]] New - Ignore Step added to Popup Menu Options in COMDEF Editor ===
| |
| − |
| |
| − | [[image:comdef_popup_v12_20111130.jpg]]
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=400>
| |
| − | * Enable and Disable IGNORE STEP choices are added to the popup menu for the command list to help change the state quickly.<br>
| |
| − | </td>
| |
| − |
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| | | | |
| | ===[[image:Check.jpg|25px]] Other === | | ===[[image:Check.jpg|25px]] Other === |
NEW - Send Part Number to Robots in Auto Mode 
