Difference between revisions of "CNC Bender v12-20111222"
From ATTWiki
| (10 intermediate revisions by one user not shown) | |||
| Line 15: | Line 15: | ||
===[[image:Check.jpg|25px]] NEW - Logic for Servo-controlled PRESSURE DIE Motion Installed === | ===[[image:Check.jpg|25px]] NEW - Logic for Servo-controlled PRESSURE DIE Motion Installed === | ||
| − | + | [[image:pressuredie_bending.jpg|250px]] | |
| − | [[image: | + | [[image:pd_servo_encoder.jpg|250px]] |
| − | + | ||
| − | + | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | * Servo-controlled pressure die positioning is | + | * Servo-controlled pressure die positioning is more accurate than standard output control.<br><br> |
* This feature is especially useful for extreme accuracy during part capture. Parts can be accurately captured by the pressure die during PREBEND (Load), BENDING, and POSTBENDING (Unloading).<br><br> | * This feature is especially useful for extreme accuracy during part capture. Parts can be accurately captured by the pressure die during PREBEND (Load), BENDING, and POSTBENDING (Unloading).<br><br> | ||
| − | |||
[[image:manual_page_PD_axis.jpg|500px]] | [[image:manual_page_PD_axis.jpg|500px]] | ||
| − | + | [[image:manual_page_PD_axis_closeup.jpg|500px]]<br> | |
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | + | ||
</td> | </td> | ||
| Line 44: | Line 41: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | PreBend Options: PD Load Capture Position | + | '''PreBend Options: PD Load Capture Position''' |
* This feature allows you to move the pressure die to a position close to the bend die for load-capture. | * This feature allows you to move the pressure die to a position close to the bend die for load-capture. | ||
</td> | </td> | ||
| Line 54: | Line 51: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | Overall Options: PD Jog Position After Bends | + | '''Overall Options: PD Jog Position After Bends''' |
* This feature allows you to open the pressure die slightly after a bend to relieve pressure before a mandrel pull. | * This feature allows you to open the pressure die slightly after a bend to relieve pressure before a mandrel pull. | ||
</td> | </td> | ||
| Line 64: | Line 61: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | Bending Options: PD Servo Retract Position | + | '''Bending Options: PD Servo Retract Position''' |
* This feature allows you to partially retract the pressure die during Multi-Bending and immediately after a bend. | * This feature allows you to partially retract the pressure die during Multi-Bending and immediately after a bend. | ||
</td> | </td> | ||
| Line 74: | Line 71: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | PostBending Options: PD Unload Capture Position | + | '''PostBending Options: PD Unload Capture Position''' |
* This feature allows you to partially retract the pressure die immediately after the last bend for unloading. | * This feature allows you to partially retract the pressure die immediately after the last bend for unloading. | ||
</td> | </td> | ||
| Line 85: | Line 82: | ||
</table> | </table> | ||
| − | |||
| − | |||
| − | |||
| − | |||
===[[image:Check.jpg|25px]] Other === | ===[[image:Check.jpg|25px]] Other === | ||
Latest revision as of 04:45, 24 December 2011
v12-20111222
|
|
NEW - Logic for Servo-controlled PRESSURE DIE Motion Installed
|
|
NEW - Options for PD Servo Motion
|
PreBend Options: PD Load Capture Position
|
|
|
Overall Options: PD Jog Position After Bends
|
|
|
Bending Options: PD Servo Retract Position
|
|
|
PostBending Options: PD Unload Capture Position
|
|
Other
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
