Difference between revisions of "VTube-LASER v1.75.1"
From ATTWiki
| (2 intermediate revisions by one user not shown) | |||
| Line 40: | Line 40: | ||
</table> | </table> | ||
| − | + | ===[[image:Check.jpg|25px]] ENHANCED: Removed the Default Radius Setup Message=== | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | ===[[image:Check.jpg|25px]] | + | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | + | The message that says that VTube will automatically set the default radius to 1.5 times the diameter no longer displays as it serves no useful purpose.</td> | |
<td width=300> | <td width=300> | ||
</td> | </td> | ||
| − | </tr> | + | </tr> |
</table> | </table> | ||
=Other Pages= | =Other Pages= | ||
*Back to [[VTube-LASER]] | *Back to [[VTube-LASER]] | ||
Latest revision as of 18:08, 3 February 2012
|
Revision 1.75.1Back to VTube-LASER |
|
ENHANCEMENT: Added Page Numbers to Reports in Print Preview
|
VTube now shows the date, time, and page numbers at the bottom of print preview reports. |
|
FIX: Previous Move During Remeasure
|
There were circumstances where VTube would backup too many steps during a remeasure. This has been repaired. |
ENHANCED: Removed the Default Radius Setup Message
| The message that says that VTube will automatically set the default radius to 1.5 times the diameter no longer displays as it serves no useful purpose. |
Other Pages
- Back to VTube-LASER
