Difference between revisions of "CNC Bender v12-20120517"
From ATTWiki
| (10 intermediate revisions by one user not shown) | |||
| Line 13: | Line 13: | ||
</table> | </table> | ||
__NOTOC__ | __NOTOC__ | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] New Feature - PDA Return in Test Bend Menu=== |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | + | You can now return the PDA in the Test Bend menu after a bend is complete. | |
| + | <br><br> | ||
| + | [[image:cnc_bender_test_bend_pda_return_closeup.jpg|300px]] | ||
| + | <br> | ||
| + | [[image:cnc_bender_test_bend_pda_return.jpg|300px]] | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | |||
</td> | </td> | ||
| Line 29: | Line 32: | ||
</table> | </table> | ||
| + | ===[[image:Check.jpg|25px]] Repaired Feature - Fix to Part Counter Boxes in Run Page === | ||
| − | ===[[image:Check.jpg|25px]] Enhanced Feature - Part Name is Now Always Trimmed === | + | <table cellpadding=10> |
| + | <tr valign=top> | ||
| + | <td width=400> | ||
| + | The part counter values would not always enable in the Run Page. This has been repaired. | ||
| + | <br><br> | ||
| + | [[image:cnc_bender_counterboxes.jpg|300px]] | ||
| + | </td> | ||
| + | |||
| + | <td width=300> | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] Enhanced Feature - The Part Name is Now Always Trimmed === | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | Preceding and trailing spaces cause problems because they are hard to detect. The part name is now always trimmed when the operator includes preceding or trailing spaces. | + | Preceding and trailing spaces cause problems because they are hard to detect. This can cause subtle problems with part synchronization (see the previous section above) when building parts to CNC Processor. |
| + | |||
| + | |||
| + | The part name is now always trimmed when the operator includes preceding or trailing spaces. | ||
</td> | </td> | ||
| Line 45: | Line 65: | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | |||
| − | |||
=Other Pages= | =Other Pages= | ||
Latest revision as of 00:29, 17 May 2012
v12-20111229
|
|
New Feature - PDA Return in Test Bend Menu
|
You can now return the PDA in the Test Bend menu after a bend is complete.
|
Repaired Feature - Fix to Part Counter Boxes in Run Page
|
The part counter values would not always enable in the Run Page. This has been repaired.
|
Enhanced Feature - The Part Name is Now Always Trimmed
|
Preceding and trailing spaces cause problems because they are hard to detect. This can cause subtle problems with part synchronization (see the previous section above) when building parts to CNC Processor.
|
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
