Difference between revisions of "VTube-STEP v1.77.3"
From ATTWiki
| (20 intermediate revisions by one user not shown) | |||
| Line 18: | Line 18: | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] ENHANCED: View Orientation Control Redesigned=== |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| + | [[image:vtube_1.77.3_vieworientation_closeup.jpg|250px]]<br><br> | ||
The View Orientation Control has new choices with graphics icons of each axes orientation.<br><br> | The View Orientation Control has new choices with graphics icons of each axes orientation.<br><br> | ||
You can click on the button or the image to find a new orientation.</td> | You can click on the button or the image to find a new orientation.</td> | ||
<td width=300> | <td width=300> | ||
| − | [[image:vtube_1.77.3_vieworientation.jpg]] | + | [[image:vtube_1.77.3_vieworientation.jpg|150px]] |
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | ===[[image:Check.jpg|25px]] NEW: | + | ===[[image:Check.jpg|25px]] NEW: Diameter Model End Lengths Change Based on New "End Adjustment Length" Values in Part Setup=== |
| + | [[image:vtube_1.77.3_EndLengthShortened_Closeup.jpg]] | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
| Line 40: | Line 42: | ||
</table> | </table> | ||
[[image:vtube_1.77.3_EndLengthShortened.jpg|500px]] | [[image:vtube_1.77.3_EndLengthShortened.jpg|500px]] | ||
| + | <br><br> | ||
| − | ===[[image:Check.jpg|25px]] REPAIR: Cut Length Calculation with End Adjustments=== | + | ===[[image:Check.jpg|25px]] REPAIR: The Cut Length Calculation with Non Zero End Adjustments Is Repaired=== |
| + | [[image:vtube_endlength_cutlength_partsetup.jpg|300px]] | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | The End Length Adjustments | + | The End Length Adjustments values are no longer doubled in the Cut Length calculation.</td> |
<td width=300> | <td width=300> | ||
| − | |||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
==Other Pages== | ==Other Pages== | ||
*Back to the [[VTube]] page | *Back to the [[VTube]] page | ||
Latest revision as of 03:26, 8 August 2012
|
Revision 1.77.3
|
|
ENHANCED: View Orientation Control Redesigned
|
|
|
NEW: Diameter Model End Lengths Change Based on New "End Adjustment Length" Values in Part Setup
| When the A-End or B-End Adjustment Lengths change, then the diameter model lengths change automatically at the next redraw. This does not change the centerline end point location. |
REPAIR: The Cut Length Calculation with Non Zero End Adjustments Is Repaired
| The End Length Adjustments values are no longer doubled in the Cut Length calculation. |
Other Pages
- Back to the VTube page
