Difference between revisions of "CNC Bender v12-20120830"
From ATTWiki
| (7 intermediate revisions by one user not shown) | |||
| Line 15: | Line 15: | ||
__NOTOC__ | __NOTOC__ | ||
| − | === [[image:Check.jpg|25px]] | + | === [[image:Check.jpg|25px]] ENHANCED: Autoloader Manual Page Redesign === |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=500> | <td width=500> | ||
| + | CNC Bender can now make the TUBE ROTATE and SEAM DETECT buttons invisible. See these two screens:<br> | ||
| + | [[image:v12-21020830_autoloader_manual_expanded.jpg|500px]]<br><br> | ||
| + | This next screen shows the two buttons removed from the screen:<br> | ||
| + | [[image:v12-21020830_autoloader_manual.jpg|500px]]<br><br> | ||
Control the visibility of buttons with new low level options: | Control the visibility of buttons with new low level options: | ||
| Line 33: | Line 34: | ||
</table> | </table> | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] NEW: Added new Processlists for Autoloader Buttons === |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | + | Three new processlists were added: | |
| + | |||
| + | #autoloader_home.cncprocesslist | ||
| + | #autoloader_liftup.cncprocesslist | ||
| + | #autoloader_liftdown.cncprocesslist | ||
| + | |||
| + | <br> | ||
| + | |||
| + | These three processlists control the jogging that occurs behind the | ||
| + | |||
| + | #Autoloader Home button | ||
| + | #Lift Up button | ||
| + | #Lift Down button | ||
| + | |||
| + | <br> | ||
| + | |||
| + | Rules: | ||
| + | # The processlists do not need to exist - however, the buttons in the manual page will do nothing unless commands are inside the processlists. | ||
| + | # No block logic is accepted ([IF], etc.) in these processlists. | ||
| + | # Parameters ARE allowed - like "= cto:5000", etc. | ||
| + | # The commands in the processlists are treated like individual jogs. | ||
| + | |||
</td> | </td> | ||
| Line 46: | Line 68: | ||
</table> | </table> | ||
| + | |||
| + | |||
| + | ===[[image:Check.jpg|25px]] NEW: Added New Help Files === | ||
| + | |||
| + | <table cellpadding=10> | ||
| + | <tr valign=top> | ||
| + | <td width=400> | ||
| + | Two new help files were added for the new low level options. | ||
| + | </td> | ||
| + | |||
| + | <td width=300> | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
=Other Pages= | =Other Pages= | ||
Latest revision as of 11:24, 30 August 2012
v12-20120830
|
|
ENHANCED: Autoloader Manual Page Redesign
|
CNC Bender can now make the TUBE ROTATE and SEAM DETECT buttons invisible. See these two screens:
|
NEW: Added new Processlists for Autoloader Buttons
|
Three new processlists were added:
These three processlists control the jogging that occurs behind the
Rules:
|
NEW: Added New Help Files
|
Two new help files were added for the new low level options. |
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
