Difference between revisions of "VTube-STEP v1.94"
(→25px ENHANCED: Automatic Projection Tolerance for Centerline Calculation) |
(→25px ENHANCED: Automatic Projection Tolerance for Centerline Calculation) |
||
| Line 80: | Line 80: | ||
===[[image:Check.jpg|25px]] ENHANCED: Automatic Projection Tolerance for Centerline Calculation === | ===[[image:Check.jpg|25px]] ENHANCED: Automatic Projection Tolerance for Centerline Calculation === | ||
<table cellpadding=10> | <table cellpadding=10> | ||
| + | |||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
Since the STEP mode calculation engine completely automates the Projection Tolerance, there is no longer a need for the user to set this value.<br><br> | Since the STEP mode calculation engine completely automates the Projection Tolerance, there is no longer a need for the user to set this value.<br><br> | ||
It is removed from above the Collection grid.<br><br> | It is removed from above the Collection grid.<br><br> | ||
| − | |||
[[image:vtube-step-1.94_projtolerance_tenth_micron.png|300px]] | [[image:vtube-step-1.94_projtolerance_tenth_micron.png|300px]] | ||
</td> | </td> | ||
| Line 91: | Line 91: | ||
</td> | </td> | ||
</tr> | </tr> | ||
| + | |||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | The Projection Tolerance in VTube-STEP now starts with an very small projection tolerance at a 10th of a micron (0.0001 mm, or 0.000003937 inches). If the centerline for the cylinders cannot be solved for, then VTube increases the projection tolerance until it finds a solution.<br><br> | ||
| + | </td> | ||
| + | <td width=500> | ||
| + | [[image:vtube-step-1.94_projtolerance_tenth_micron.png|400px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
</table> | </table> | ||
Revision as of 20:43, 27 July 2014
|
Revision 1.94
|
|
- See VTube-STEP Customer Support Page to download the latest version.
NEW: Trim Surface Datum for Trimming or Extending End Lengths
|
VTube-STEP now allows for different kind of Trim Surfaces now. Older versions only allow for the centroid (average XYZ point) of all points in a solid used to trim. |
|
|
|
|
|
|
|
NEW: Add Collection Grid Properties Column and Edit Datum Menu
|
The new properties column allows for new options to accompany each of the collected objects. Right click on any TrimSurf row, then choose Edit Trim Surface Datum to enter this menu (below): |
|
ENHANCED: Automatic Projection Tolerance for Centerline Calculation
|
Since the STEP mode calculation engine completely automates the Projection Tolerance, there is no longer a need for the user to set this value. |
|
|
The Projection Tolerance in VTube-STEP now starts with an very small projection tolerance at a 10th of a micron (0.0001 mm, or 0.000003937 inches). If the centerline for the cylinders cannot be solved for, then VTube increases the projection tolerance until it finds a solution. |
|
NEW: Automatic Set of End Diameters When Calculating Centerlines
|
The end diameters are now set to equal the main diameter during centerline calculation from models. |
|
NEW: Added to the Popup Menu to Synchronize End Diameters with Main Diameter
|
The pop up menus for the Part Setup menu (STEP and LASER modes) now allow for the end diameters to be synchronized with the main diameter. |
|
ENHANCED: Fine-Tune Export to Laservision Spreadsheet Format Files
|
The Eaton Leonard Laservision measuring center can import CSV (Comma Separated Value) files built in an Excel spreadsheet. This version of VTube can now export to this format. This version fine-tunes the new feature to make the output conform to customer specifications for the project. |
 |
NEW: Previous Paths List in Quick Open
|
The Quick Open dialog now has a pull-down list that shows all the recent previous paths used to load VTube project files or imported solid model files. |
 |
Other Changes
|
Other Pages
- Back to VTube-STEP
- Back to VTube Software Updates (for LASER Mode)
- Back to VTube-LASER
