Difference between revisions of "VTube-LASER v2.1.2"

From ATTWiki
Jump to: navigation, search
(→‎25px ENHANCED: Improved Graphics)
(→‎25px NEW: Winton WMC Bender Data File Setup Window)
Line 33: Line 33:
 
</table>
 
</table>
  
−
===[[image:Check.jpg|25px]] NEW: Winton WMC Bender Data File Setup Window===
+
===[[image:Check.jpg|25px]] NEW: STEP Export is Faster for Large Models===
−
 
+
<table cellpadding=10>
−
<table cellpadding=10 width=800>
+
 
<tr valign=top>
 
<tr valign=top>
−
<td width=300>
+
<td width=400>
−
The new window allows VTube users to edit the data inside a Winton WMC file before exporting or adjusting a WMC file.<br><br>
+
The export speed on large models is now several times faster than in previous versions.<br><br>
−
[[image:vtube-laser-2.00_WintonWMC_Editor_Closeup.png|300px]]
+
If you export STEP files, then this is an important update for you.
 
</td>
 
</td>
−
<td width=500>
+
<td width=400>
−
[[image:vtube-laser_2.00_WintonBenderDataSetupEditor.png|500px]]
+
[[image:vtube-step-2.1.2_stepexport.png|400px]]<br><br>
 
</td>
 
</td>
 
</tr>
 
</tr>

Revision as of 19:28, 14 June 2015

Vtube-laser logo.jpg

Revision 2.1.2

Vtube-laser 1.89 mainscreen.png



Check.jpg ENHANCED: Improved Graphics

  • Perspective projection is much improved.

  • Point labels drawing has improved logic and is much faster.

Vtube-laser 2.1.2 hvac with points.png

Check.jpg NEW: STEP Export is Faster for Large Models

The export speed on large models is now several times faster than in previous versions.

If you export STEP files, then this is an important update for you.

Vtube-step-2.1.2 stepexport.png

Check.jpg NEW: SUPRAVISION Network Engine Now Handles Benders with Inverted Rotations

The Supravision network engine now allows for rotations to be inverted for benders that have rotations that move in the opposite direction to VTube.

Vtube-2 cwrotation svnetwork.png

Check.jpg ENHANCED: CSM and ALPINE File Data Transfer Tested and Improved

  • The CSM and Alpine conversions now correctly invert the rotation value in both M3 and M4 controls - since they move in the opposite direction from VTube rotations.

  • Other adjustments and fixes to the conversion were tested with both styles of bender controls.

  • When VTube sends corrections to the M4 controls, it now changes the adjustment values rather than the nominal values in the YBC page.

Alpinebender.png



Check.jpg Other Changes

  • The VTube configuration file location was changed to the more standard "c:\ProgramData\VTube" location.

  • The installation performs a better job of setting up the configuration file location.

  • The Supravision network engine has been enhanced to handle data files that don't follow the Supravison spec perfectly.

  • We fixed a ball probe measurement issue where VTube would sometimes not always take in single points from the FARO driver. This issue created problems with measuring cut planes too. If you measured cut planes, and still couldn't get the cut plane to work properly, then it was probably due to this issue.


Other

Retrieved from "http://www.advancedtubular.wiki/index.php?title=VTube-LASER_v2.1.2&oldid=26685"