Difference between revisions of "Reverse the Tube Ends"
From ATTWiki
(Created page with "<table> <tr cellpadding=10> <td width=225> 200px 200px * Back to VTube-STEP * Back to [[VTube-LASER]...") |
(→Reset the Reversed Point Labels) |
||
| (8 intermediate revisions by one user not shown) | |||
| Line 23: | Line 23: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | + | It is often necessary to reverse the tube ends in order to bend the part from the other end of the tube. To reverse the tube ends, you can right click on the XYZ grids for the MASTER or MEASURED data and click on '''Reverse XYZ Data'''. | |
| − | + | ||
</td> | </td> | ||
<td> | <td> | ||
| − | [[image:vtube-laser_v2. | + | [[image:vtube-laser_v2.5_reverse_tubeends.png|400px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 34: | Line 33: | ||
<br> | <br> | ||
| − | == | + | == Reversed Point Labels== |
<table> | <table> | ||
| Line 40: | Line 39: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | + | When you reverse the XYZ rows, VTube will also reverse the point labels.<br><br>With the point labels reversed, it is a good idea to look at the END LABELS rather than the POINT LABELS to determine which end to measure first.<br><br> | |
| − | </td> | + | See the effect in the image on the right. The END A label is at point 9 in this part after a reverse of the XYZ data.</td> |
<td> | <td> | ||
| − | [[image:vtube- | + | [[image:vtube-laser_2.5_reverse_point_labels.png|400px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 51: | Line 50: | ||
| − | == | + | == Reset the Reversed Point Labels== |
<table> | <table> | ||
| Line 57: | Line 56: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | + | You can reset the point labels from being reversed with the XYZ reverse feature.<br><br> | |
| − | + | Right click on the XYZ grid and the click on '''Reset Point Labels'''.</td> | |
| − | + | ||
| − | + | ||
| − | </td> | + | |
<td> | <td> | ||
| − | [[image: | + | [[image:vtube_v2.5_reset_point_ labels.png|400px]] |
| + | [[image:vtube_v2.5_effect_of_reset_point_labels.png|400px]]<br><br> | ||
| + | [[image:vtube-laser_v2.5_tubeimage_with_pointlabels.png|400px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
Latest revision as of 15:48, 13 April 2016
|
|
|
Reverse the Tube Ends
|
It is often necessary to reverse the tube ends in order to bend the part from the other end of the tube. To reverse the tube ends, you can right click on the XYZ grids for the MASTER or MEASURED data and click on Reverse XYZ Data. |
|
Reversed Point Labels
|
When you reverse the XYZ rows, VTube will also reverse the point labels. |
|
Reset the Reversed Point Labels
|
You can reset the point labels from being reversed with the XYZ reverse feature. |
|
Other Pages
- Back to the VTube-STEP page
- Back to the VTube-LASER page
