Difference between revisions of "VTube Communication with AMOB"

From ATTWiki
Jump to: navigation, search
(Other Pages)
 
(57 intermediate revisions by one user not shown)
Line 1: Line 1:
[[image:vtube_v2.5_image to amob.png|900px]]
+
 
 +
[[image:amob_bender_and_logo.png]]<br><br>
  
 
==About this Page==
 
==About this Page==
 
<table width=1000>
 
<table width=1000>
 
<tr valign=top>
 
<tr valign=top>
<td width=300>
+
<td width=500>
 
This page describes the setup and use of the VTube to AMOB communications.<br><br>
 
This page describes the setup and use of the VTube to AMOB communications.<br><br>
 +
[[image:vtube_v2.5_image to amob.png|600px]]
 
</td>
 
</td>
 
<td width=500>
 
<td width=500>
Line 15: Line 17:
 
__NOTOC__
 
__NOTOC__
  
==Tested and Verified Communications==
+
==The Basics of How It Works==
 
<table width=1000>
 
<table width=1000>
 
<tr valign=top>
 
<tr valign=top>
<td width=300>
 
The developers from SOCO, TFS, and Advanced Tubular have thoroughly tested the features explained in this page.<br><br>If you have any questions, please contact [mailto:[email protected] Michael Cone at Advanced Tubular Technologies], or [mailto:[email protected] Kyle Eagle at TFS] (Tube Form Solutions - Distributor for SOCO).<br><br>
 
See [http://www.advancedtubular.wiki/index.php/VTube-LASER_Videos#Video_62:_Setup_and_Correct_SOCO_Benders_with_VTube-LASER_Communications Video 62 - SOCO Communications Video] to see an actual corrections loop with a SOCO bender.
 
</td>
 
 
<td width=500>
 
<td width=500>
</td>
+
* VTube sends data to the AMOB by exporting a ".VTL" file that the AMOB can read. Communications can be setup through a standard Windows network connection, or you can use a thumb drive.<br><br>
</tr>
+
 
</table>
+
* The communication is unidirectional toward the bender. It is not possible to RECALL data from the AMOB using this file.  The AMOB control only reads this file data.<br><br>  
  
==Protocol==
+
* The data that is included in the VTL file that the AMOB can read is the '''BENDER data (X axis, Y Axis, C Axis)'''. The data also includes the '''diameter''', '''wall thickness''', and '''cut length'''.<br><br>
<table>
+
<tr valign=top>
+
<td width=300>
+
[[VTube-STEP]] can export Supravision data to SOCO benders using the SOCO SVNet protocol.<br><br> 
+
[[VTube-LASER]], the version of VTube that connects to a FARO measuring center arm, can send measured data to the SOCO control for corrections.<br><br>
+
[[image:faro_scanner_v6.png|300px]]
+
 
</td>
 
</td>
<td width=300>
+
<td width=500>
[[image:VTube-LASER to Soco XYZ.png|500px]]
+
 
</td>
 
</td>
 
</tr>
 
</tr>
 
</table>
 
</table>
  
==Communications Setup at the SOCO Bender==
+
==Communications Setup at the AMOB Bender==
 
<table>
 
<table>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=500>
 
<td width=500>
  
* Correct communications requires at least Revision 728 (September 10, 2016) of the SOCO software. (The control filenames include the revision number in the name like this: "NVS728.exe". The executable file is in the "c:\Program Files (x86)\Bending Machine" folder. You can see the SOCO NVC revision number also at the bottom of the startup screen (See the right image.)<br><br>
+
* Connect the AMOB bender to the network using a standard Ethernet cable.<br><br>
* Connect the SOCO bender to the network using a standard Ethernet cable.  SOCO computers can be accessed through the lower front of the operator station. Run the cable through the small side door on the right, and up to the computer system. The SOCO control computer will have Ethernet ports available for connection.<br><br>
+
* Setup a shared network location either in the AMOB windows control or in a network path on your network.<br><br>
* Setup a shared network location either in the SOCO windows control or in a network path on your network.<br><br>
+
* If you share a folder on the AMOB control, then create a user with a username and password that can be used to login to the computer from the VTube-LASER computer.<br><br>
* In the SOCO YBC screen, press the measuring center button.<br><br>
+
* Enter the shared network path in the Exchange Directory field. This path name cannot be a UNC name (like \\192.168.0.2\VTube\).  It must be a path with a drive and a path that follows. If you must network to a location on the network, then map a drive letter to that location, and use the mapped drive letter in this field.<br><br>
+
* Enter the bender number. Each bender number needs to have a unique number in the network. The bender number must be 1 or higher.  Don't use "0" for the bender number, because VTube requires a bender number that is at least 1.<br><br>
+
* Activate the SV/SV Network communications. Touch the checkbox field until it shows a check mark (see the image on the right).<br><br>
+
  
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
[[image:Soco Startup Screen.png|500px]]<br><br>
+
[[image:amob_program_machine_configuration_press_FARO.png|500px]]<br><br>
[[image:Soco Measuring Center Setup.png|500px]]
+
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 78: Line 64:
 
</table>
 
</table>
  
===Setup the Benderlink Network Grid for the SOCO Bender===
+
===Setup the Benderlink Network Grid for the AMOB Bender===
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
#Choose an unused row in the grid for a new SOCO bender setup. (Click on the image at the right to see a zoomed image.)<br><br>
+
#Choose an unused row in the grid for a new AMOB bender setup. (Click on the image at the right to see a zoomed image.)<br><br>
 
#Assign a bender name that will help operators identify what this bender is.  This text will be displayed at the top of the Bender Setup menu.<br><br>
 
#Assign a bender name that will help operators identify what this bender is.  This text will be displayed at the top of the Bender Setup menu.<br><br>
#Assign the SOCO SVNet protocol.<br><br>
+
#Set the protocol to AMOB VTL Data.<br><br>
#Enter the path to the shared drive or folder in the NetPath field. Use the same location as the SOCO setup. VTube accepts UNC names as well as regular paths with drive letters.<br><br>
+
#Enter the path to the shared drive or folder in the NetPath field. Use the same location as the AMOB setup. VTube accepts UNC names as well as regular paths with drive letters.<br><br>
 
#Enter the IP address in the PING IP ADDRESS field if it is a fixed field. (This is not required. It allows VTube to ping the address to see if the network location is active before trying to open communications.)<br><br>
 
#Enter the IP address in the PING IP ADDRESS field if it is a fixed field. (This is not required. It allows VTube to ping the address to see if the network location is active before trying to open communications.)<br><br>
 
#Press Close to save the settings.  VTube will save these values to a persistent configuration file that will not change unless you change them in this grid.
 
#Press Close to save the settings.  VTube will save these values to a persistent configuration file that will not change unless you change them in this grid.
Line 91: Line 77:
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
[[image:VTube Benderlink Setup for SOCO SVNet.png|600px]]
+
[[image:VTube Benderlink Setup for AMOB VTL.png|600px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 97: Line 83:
 
</table>
 
</table>
  
==How to SEND MASTER XYZ Data to the SOCO Control from VTube-STEP==
+
==How to SEND MASTER BENDER Data to the AMOB Control from VTube-STEP==
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
  
You can import data into VTube-STEP then send the XYZ Centerline data calculated to the SOCO bender using the VTube Bender Output menu.<br><br>
+
You can import data into VTube-STEP then send the bender data calculated to the AMOB bender using the VTube Input/Export menu.<br>
===At the SOCO Control===
+
At the SOCO control, enter the SOCO XYZ Screen. With the XYZ Screen open, the SOCO control will understand that it must extract the MASTER XYZ data in the incoming data and import that into the SOCO NVS software.<br><br>
+
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:socoXYZscreen.png|600px]]<br><br>
 
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 117: Line 100:
 
<td width=300>
 
<td width=300>
  
===At the VTube-STEP Computer===
+
===At the VTube-STEP Main Screen===
Move to the VTube-STEP computer and follow these steps to transfer the XYZ data to the SOCO.
+
Move to the VTube-STEP computer and follow these steps to transfer the bender data to the AMOB.
  
# Press the Bender Output button in the navigation pane.  
+
# Press the Import/Export button in the navigation pane.  
# Set the correct bender number.
+
# Find and press the AMOB VTL Data button in the Export section.
# Press the Send to Bender button.
+
<br>
+
The SOCO will receive new data and ask if it should be imported with a dialog.  Press YES to import the data.
+
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:VTube-STEP Bender Output to SOCO.png|600px]]
+
[[image:vtube-step_v2.7_AMOB_Export_Button.png|600px]]
  
 
</td>
 
</td>
Line 133: Line 113:
 
</table>
 
</table>
  
<br><br>
 
 
==How to SEND MASTER XYZ Data to the SOCO Control from VTube-LASER==
 
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
  
You can also send the new XYZ Centerline data from the VTube-LASER BENDER SETUP menu to the SOCO bender using the VTube Bender Output menu.<br><br>
+
===At the AMOB Bender Data Export Window (inside VTube-STEP)===
 
+
Press the Export button to save a VTL file on the network at the shared path for the AMOB bender.
===Enter the XYZ Screen At the SOCO Control===
+
At the SOCO control, enter the XYZ Screen. With the XYZ Screen open, the SOCO control will understand that it must extract the MASTER XYZ data in the incoming data and import that into the SOCO NVS software.<br><br>
+
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:socoXYZscreen.png|600px]]
+
[[image:vtube-step_v2.7_AMOB_Export_Window.png|600px]]
 +
 
 
</td>
 
</td>
 
</tr>
 
</tr>
 
</table>
 
</table>
  
<table cellpadding=10>
 
<tr valign=top>
 
<td width=300>
 
  
===Enter the BENDER SETUP menu in VTube-LASER===
+
<br><br>
Follow these steps in the VTube-LASER:
+
  
Press the "BENDER SETUP button in the Navigation Pane.
+
==How to SEND CORRECTION Data to the AMOB Control from VTube-LASER==
</td>
+
 
<td width=400>
+
===After Bending the Tube===
[[image:vtube-laser_2.7_bendersetup_button_navigationpane.png|400px]]<br><br>
+
Bend a tube then measure it with VTube-LASER.<br><br>
</td>
+
</tr>
+
</table>
+
  
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
STEP 1 - Set the correct bender number at the top of the window. As of version 2.7, the SOCO SVNet option is available - which means you should see a SOCO bender at the top left corner of the screen.
 
  
 
+
===Measure the tube with VTube-LASER===
STEP 2 - On the right click on "Setup the Bender".
+
Measure and align the tube to determine if it qualifies by falling within the envelope tolerance for the tube shape.
 
+
 
+
STEP 3 - Click on AUTO SEND
+
 
<br><br>
 
<br><br>
The SOCO will receive new data and ask if it should be imported with a dialog. Press YES to import the data.
+
In the VTube-LASER screen shot, you see the actual result of the first tube not qualifying in shape. The red cells in the tangent point grid on the lower left show that the measured tube centerline is out-of-tolerance.
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:vtube-laser_v2.7_send_master_to_soco.png|600px]]
+
[[image:vtube-laser_v2.7_soco_part_measure.png|600px]]<br><br>
 +
[[image:vtube-laser_v2.7_soco_out_of_tolerance.png|600px]]<br><br>
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 186: Line 152:
  
  
<br><br>
 
  
==How to SEND CORRECTION Data to the SOCO Control from VTube-LASER==
 
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
  
===At the SOCO Control===
+
===Correct the AMOB with VTube-LASER - Enter BENDER SETUP===
At the SOCO control, setup and bend the first tube through the YBC and then Compile Execution screen.<br><br>
+
Follow these steps in the VTube-LASER:
 +
 
 +
Press the "BENDER SETUP button in the Navigation Pane.
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:soco_compile_execution_screen.png|600px]]
+
[[image:vtube-laser_2.7_bendersetup_button_navigationpane.png|400px]]<br><br>
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 206: Line 172:
 
<td width=300>
 
<td width=300>
  
===After Bending the Tube===
+
===INITIAL Setup of Bender Setup Window===
After the bending cycle is complete, remove the tube from the dies. Leave the bender in AUTO mode.<br><br>
+
The first time in this window for a new part will require these steps before you can correct the AMOB bender.<br><br>
 +
 
 +
STEP 1 - Set the correct bender number at the top of the window. The AMOB bender should display if you have already setup the bender protocol in the Benderlink grid.
 +
 
 +
 
 +
STEP 2 - Click on the "Setup This Window" button.
 +
 
 +
 
 +
STEP 3 - Click on the "Copy Master LRA to Setup LRA" button.
 +
 
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:soco_remove_part_from_bender.png|600px]]
+
[[image:VTL Bender Setup AMOB Bender New Setup.png|600px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 220: Line 195:
 
<td width=300>
 
<td width=300>
  
===Measure the tube with VTube-LASER===
+
===Check the BLUE COLUMN Data===
Measure and align the tube to determine if it qualifies by falling within the envelope tolerance for the tube shape.
+
The LRA blue column data is now filled with the MASTER LRA data.
 +
 
 +
This data MUST match the X axis, Y axis, Z axis bender data at the bender - or the corrections will be incorrect.  
 
<br><br>
 
<br><br>
In the VTube-LASER screen shot, you see the actual result of the first tube not qualifying in shape. The red cells in the tangent point grid on the lower left show that the measured tube centerline is out-of-tolerance.
+
 
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:vtube-laser_v2.7_soco_part_measure.png|600px]]<br><br>
+
[[image:VTL Bender Setup AMOB After Master Data Import.png|600px]]
[[image:vtube-laser_v2.7_soco_out_of_tolerance.png|600px]]<br><br>
+
 
</td>
 
</td>
 
</tr>
 
</tr>
 
</table>
 
</table>
 
  
  
Line 238: Line 213:
 
<td width=300>
 
<td width=300>
  
===Correct the SOCO with VTube-LASER - Enter BENDER SETUP===
+
===Send the Corrections to the AMOB VTL File===
Follow these steps in the VTube-LASER:
+
Save the Correction data to the file for the AMOB to import.
 +
<br><br>
 +
STEP 1 - Click on Bidirectional Communication<br><br>
 +
STEP 2 - Click on AUTO SEND.<br><br>
 +
STEP 3 - Save the new VTL file to the network location.
  
Press the "BENDER SETUP button in the Navigation Pane.
 
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:vtube-laser_2.7_bendersetup_button_navigationpane.png|400px]]<br><br>
+
[[image:VTL Bender Setup AMOB Correction.png|600px]]<br><br>
 
</td>
 
</td>
 
</tr>
 
</tr>
 
</table>
 
</table>
  
<table cellpadding=10>
 
<tr valign=top>
 
<td width=300>
 
  
===RECALL SOCO YBC data and then SEND CORRECTIONS===
 
STEP 1 - Set the correct bender number at the top of the window. As of version 2.7, the SOCO SVNet option is available - which means you should see a SOCO bender at the top left corner of the screen.
 
 
 
STEP 2 - If the Part Number is empty, then press the Copy the Master Part Setup values.
 
 
 
STEP 3 - Click on RECALL. This will update the BLUE columns in the Bender Setup.
 
 
 
STEP 4 - You can manually change the ADJUSTMENT values before sending corrections. In this case, we set the first and last Length adjustment to zero in order to keep the start position of the carriage in the same place.
 
 
 
STEP 5 - Click on AUTO SEND. This will send the ORANGE columns to the SOCO bender.
 
</td>
 
<td width=400>
 
[[image:vtube-laser_v2.7_soco_send_correction.png|600px]]
 
</td>
 
</tr>
 
</table>
 
  
 +
<br><br>
  
 
<table cellpadding=10>
 
<table cellpadding=10>
Line 279: Line 235:
 
<td width=300>
 
<td width=300>
  
===At the SOCO Bender - Press GO!===
+
===Import the Correction Data at the AMOB Control===
Press GO!  The SOCO will compile the changes.
+
Save the Correction data to the file for the AMOB to import.
 
+
You will see a progress bar after you press GO!
+
 
<br><br>
 
<br><br>
[[image:soco_press_go_compile_execution_progressbar.png|300px]]
+
STEP 1 - Enter the Program Machine Configuration menu. <br><br>
 +
STEP 2 - Press the FARO (or it may be "VTube") button<br><br>
 +
STEP 3 - Open the VTL file.<br><br>
 +
 
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:soco_press_go_compile_execution.png|600px]]
+
[[image:amob_program_machine_configuration_press_FARO.png|500px]]<br><br>
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 296: Line 253:
 
<td width=300>
 
<td width=300>
  
The "Auto Compensation Completed" message will appear in the lower right corner.
+
===AMOB Control Bender Data Updated===
 +
The bender data will be updated with the new values.<br><br>
 +
Bend the corrected part.
  
Bend the corrected part now.
 
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:soco_auto_compensation_completed.png|600px]]
+
[[image:AMOB bender data screen.png|500px]]<br><br>
 
</td>
 
</td>
 
</tr>
 
</tr>
 
</table>
 
</table>
 +
 +
 +
 +
 +
==Synchronizing the VTube-LASER and AMOB Data Before Corrections==
  
 
<table cellpadding=10>
 
<table cellpadding=10>
Line 310: Line 273:
 
<td width=300>
 
<td width=300>
  
===Measure at the VTube-LASER Computer===
+
It is critical to be sure the blue columns contain the same data that the AMOB X Axis, Y Axis, Z axis values have before correction is applied.<br><br>
Measure and align the tube again to determine if it qualifies by falling within the envelope tolerance for the tube shape.
+
 
<br><br>
+
To make the data the value the same for the next correction, you can press the bottom button in the Bidirectional Communications menu on the right. Be sure you do this BEFORE you measure the next corrected part.<br><br>
This screen shot shows an actual resulting change after the correction.
+
 
 +
The reason for this step is because the AMOB does not allow VTube to RECALL data in order to update the BLUE columns for the next correction. So this process must be performed manually.<br><br>
 +
 
 +
The data in the blue and the orange columns will now be identical. You can exit this window and measure the next corrected part.
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:vtube-laser_v2.7_soco_part_qualifies.png|600px]]<br><br>
+
[[image:Combine Adjusted back into LRA then CLEAR Adjusted.png]]<br><br>
 +
[[image:Adjusted data combined into blue columns.png|600px]]<br><br>
 
</td>
 
</td>
 
</tr>
 
</tr>
 
</table>
 
</table>
 
 
 
<br><br>
 
  
 
==Other Pages==
 
==Other Pages==
 
* See [[VTube-LASER]]
 
* See [[VTube-LASER]]
 
* See [[VTube-STEP]]
 
* See [[VTube-STEP]]
* See [[SOCO]] for information on the SOCO benders
 
* See [http://www.advancedtubular.wiki/index.php/VTube-LASER_Videos#Video_62:_Setup_and_Correct_SOCO_Benders_with_VTube-LASER_Communications Video 62 - SOCO Communications Video] to see an actual corrections loop with a SOCO bender.
 

Latest revision as of 17:55, 24 January 2017

Amob bender and logo.png

About this Page

This page describes the setup and use of the VTube to AMOB communications.

Vtube v2.5 image to amob.png


The Basics of How It Works

  • VTube sends data to the AMOB by exporting a ".VTL" file that the AMOB can read. Communications can be setup through a standard Windows network connection, or you can use a thumb drive.

  • The communication is unidirectional toward the bender. It is not possible to RECALL data from the AMOB using this file. The AMOB control only reads this file data.

  • The data that is included in the VTL file that the AMOB can read is the BENDER data (X axis, Y Axis, C Axis). The data also includes the diameter, wall thickness, and cut length.

Communications Setup at the AMOB Bender

  • Connect the AMOB bender to the network using a standard Ethernet cable.

  • Setup a shared network location either in the AMOB windows control or in a network path on your network.

  • If you share a folder on the AMOB control, then create a user with a username and password that can be used to login to the computer from the VTube-LASER computer.

Amob program machine configuration press FARO.png

Setup Benderlink at VTube-STEP or VTube-LASER

Entering Benderlink Setup

  1. Enter the VTube System Options menu.

  2. Enter the Measure 2 tab menu.

  3. Enter the Setup Benderlink Network menu.

VTube System Options Benderlink Network Button.png

Setup the Benderlink Network Grid for the AMOB Bender

  1. Choose an unused row in the grid for a new AMOB bender setup. (Click on the image at the right to see a zoomed image.)

  2. Assign a bender name that will help operators identify what this bender is. This text will be displayed at the top of the Bender Setup menu.

  3. Set the protocol to AMOB VTL Data.

  4. Enter the path to the shared drive or folder in the NetPath field. Use the same location as the AMOB setup. VTube accepts UNC names as well as regular paths with drive letters.

  5. Enter the IP address in the PING IP ADDRESS field if it is a fixed field. (This is not required. It allows VTube to ping the address to see if the network location is active before trying to open communications.)

  6. Press Close to save the settings. VTube will save these values to a persistent configuration file that will not change unless you change them in this grid.

VTube Benderlink Setup for AMOB VTL.png

How to SEND MASTER BENDER Data to the AMOB Control from VTube-STEP

You can import data into VTube-STEP then send the bender data calculated to the AMOB bender using the VTube Input/Export menu.


At the VTube-STEP Main Screen

Move to the VTube-STEP computer and follow these steps to transfer the bender data to the AMOB.

  1. Press the Import/Export button in the navigation pane.
  2. Find and press the AMOB VTL Data button in the Export section.

Vtube-step v2.7 AMOB Export Button.png

At the AMOB Bender Data Export Window (inside VTube-STEP)

Press the Export button to save a VTL file on the network at the shared path for the AMOB bender.

Vtube-step v2.7 AMOB Export Window.png




How to SEND CORRECTION Data to the AMOB Control from VTube-LASER

After Bending the Tube

Bend a tube then measure it with VTube-LASER.

Measure the tube with VTube-LASER

Measure and align the tube to determine if it qualifies by falling within the envelope tolerance for the tube shape.

In the VTube-LASER screen shot, you see the actual result of the first tube not qualifying in shape. The red cells in the tangent point grid on the lower left show that the measured tube centerline is out-of-tolerance.

Vtube-laser v2.7 soco part measure.png

Vtube-laser v2.7 soco out of tolerance.png


Correct the AMOB with VTube-LASER - Enter BENDER SETUP

Follow these steps in the VTube-LASER:

Press the "BENDER SETUP button in the Navigation Pane.

Vtube-laser 2.7 bendersetup button navigationpane.png

INITIAL Setup of Bender Setup Window

The first time in this window for a new part will require these steps before you can correct the AMOB bender.

STEP 1 - Set the correct bender number at the top of the window. The AMOB bender should display if you have already setup the bender protocol in the Benderlink grid.


STEP 2 - Click on the "Setup This Window" button.


STEP 3 - Click on the "Copy Master LRA to Setup LRA" button.

VTL Bender Setup AMOB Bender New Setup.png


Check the BLUE COLUMN Data

The LRA blue column data is now filled with the MASTER LRA data.

This data MUST match the X axis, Y axis, Z axis bender data at the bender - or the corrections will be incorrect.

VTL Bender Setup AMOB After Master Data Import.png


Send the Corrections to the AMOB VTL File

Save the Correction data to the file for the AMOB to import.

STEP 1 - Click on Bidirectional Communication

STEP 2 - Click on AUTO SEND.

STEP 3 - Save the new VTL file to the network location.

VTL Bender Setup AMOB Correction.png




Import the Correction Data at the AMOB Control

Save the Correction data to the file for the AMOB to import.

STEP 1 - Enter the Program Machine Configuration menu.

STEP 2 - Press the FARO (or it may be "VTube") button

STEP 3 - Open the VTL file.

Amob program machine configuration press FARO.png

AMOB Control Bender Data Updated

The bender data will be updated with the new values.

Bend the corrected part.

AMOB bender data screen.png



Synchronizing the VTube-LASER and AMOB Data Before Corrections

It is critical to be sure the blue columns contain the same data that the AMOB X Axis, Y Axis, Z axis values have before correction is applied.

To make the data the value the same for the next correction, you can press the bottom button in the Bidirectional Communications menu on the right. Be sure you do this BEFORE you measure the next corrected part.

The reason for this step is because the AMOB does not allow VTube to RECALL data in order to update the BLUE columns for the next correction. So this process must be performed manually.

The data in the blue and the orange columns will now be identical. You can exit this window and measure the next corrected part.

Combine Adjusted back into LRA then CLEAR Adjusted.png

Adjusted data combined into blue columns.png

Other Pages