Difference between revisions of "CNC Bender v10-20071003"
(→How to UPGRADE) |
(→How to UPGRADE) |
||
| Line 76: | Line 76: | ||
*[[CNC Bender v10-20070914]] | *[[CNC Bender v10-20070914]] | ||
| + | ===UPGRADE TERMS=== | ||
<br> | <br> | ||
| − | + | <table cellpadding=25> | |
| − | <table cellpadding= | + | |
<tr> | <tr> | ||
| − | <td width = 200 bgcolor="#f0f0f0"> | + | <td width = 200 bgcolor="#f0f0f0">First 90 Days </td> |
| − | <td> | + | <td>If your system is new or was upgraded in the last 90 days, then the upgrade is free. Please call us for a password to unlock the setup file after you have downloaded the file.</td> |
</tr> | </tr> | ||
<tr> | <tr> | ||
| − | <td width = 200 bgcolor="#ffffff"> | + | <td width = 200 bgcolor="#ffffff">After 90 Days </td> |
<td> If your system can be upgraded with a simple file installation, then there is an upgrade fee that, once payment is complete, we will send you a password to unlock the setup file after you have downloaded the file.</td> | <td> If your system can be upgraded with a simple file installation, then there is an upgrade fee that, once payment is complete, we will send you a password to unlock the setup file after you have downloaded the file.</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
| − | <td width = 200 bgcolor="#f0f0f0"> | + | <td width = 200 bgcolor="#f0f0f0">Older Systems </td> |
<td> Some systems require an on-site visit from a CNC Bender technician. Please call us for a quotation to visit your site for an upgrade to your system.</td> | <td> Some systems require an on-site visit from a CNC Bender technician. Please call us for a quotation to visit your site for an upgrade to your system.</td> | ||
</tr> | </tr> | ||
Revision as of 22:44, 5 October 2007
Contents |
CHANGES to CNC BENDER
Automatic Cross Check for Module Configuration Files
CNC Bender cannot operate properly if the module configuration files are setup improperly. CNC Bender now performs a module configuration cross check diagnostic every time it starts.
If the configuration files are not perfectly matched, then you will see this warning:
Update to File Load User Window
The File Load menu User Interface adjusted slightly in order to be more consistent with other CNC Bender menus.
ORIGINAL:
NEW this VERSION
CHANGES to CNC PROCESSOR
CNC Processor is the program that directly controls the bender actuators.
Disallow Jog Queuing When in Cycle Hold Mode
CNC Bender no longer allows an operator to jog any axis or actuator if the Cycle Hold button is pressed. This mode is slightly different than Safe Mode Cycle Hold, where the safety scanner area is entered. When the safety scanner or mat is activated, the machine changes to a near Zero Energy State state.
Cycle Hold without stepping on the mat or safety scanner acts as a pause button without changing the bender into safe mode.
|
|
Reduced CPU Usage When Idle
CNC Processor required expanded CPU usage when the bender was powered down or in manual mode. This had an effect of slowing the CNC Bender user interface.
Starting with this version, CNC Processor automatically reduces the load on the CPU when in either of these modes.
How to UPGRADE
If your operator station contains one of the versions listed below, then they can be upgraded through simple self-installation:
- CNC Bender v10-20070928
- CNC Bender v10-20070920
- CNC Bender v10-20070726b
- CNC Bender v10-20070803
- CNC Bender v10-20070828
- CNC Bender v10-20070914
UPGRADE TERMS
| First 90 Days | If your system is new or was upgraded in the last 90 days, then the upgrade is free. Please call us for a password to unlock the setup file after you have downloaded the file. |
| After 90 Days | If your system can be upgraded with a simple file installation, then there is an upgrade fee that, once payment is complete, we will send you a password to unlock the setup file after you have downloaded the file. |
| Older Systems | Some systems require an on-site visit from a CNC Bender technician. Please call us for a quotation to visit your site for an upgrade to your system. |
Download the setup file by clicking on this link.
Note: This setup file requires a password to run. Please contact John Esralian for upgrade prices and password information.
