Difference between revisions of "CNCProcessor.cfg"
From ATTWiki
(→Sections) |
|||
| Line 14: | Line 14: | ||
<pre> | <pre> | ||
| − | [ | + | [Machine Lube] |
| − | + | Machine Lube Duration=5000 | |
| − | Machine Lube Duration= 5000 | + | Lube Machine At Bend Count=100 |
| − | Lube Machine At Bend Count= | + | Pulse Machine Lube Pump=1 |
| + | Watch For Machine Lube Complete Input=0 | ||
[CIO] | [CIO] | ||
| − | CIO Name Of Input Clamp Die Close= | + | CIO Name Of Input Clamp Die Close=Input_ClampIsClosed_End |
CIO Name Of Input Pressure Die Home=Input_PressureDieIsHome_End | CIO Name Of Input Pressure Die Home=Input_PressureDieIsHome_End | ||
| − | CIO Name Of Input Pressure Die Close= | + | CIO Name Of Input Pressure Die Close=Input_PressureDieIsClosed_End |
CIO Name Of Input Carriage Cross Slide Advance=Input_CarriageCrossSlideIsAdvanced_End | CIO Name Of Input Carriage Cross Slide Advance=Input_CarriageCrossSlideIsAdvanced_End | ||
| − | CIO Name Of Input Release Button= Input_Release_Button_End | + | CIO Name Of Input Release Button=Input_Release_Button_End |
| − | CIO Name Of Output Release Illuminate= Output_Release_Illuminate | + | CIO Name Of Output Release Illuminate=Output_Release_Illuminate |
| − | CIO Name Of Boost Bottom Advance= Output_BoostBottom_Advance | + | CIO Name Of Boost Bottom Advance=Output_BoostBottom_Advance |
| − | CIO Name Of Boost Top Advance= Output_BoostTop_Advance | + | CIO Name Of Boost Top Advance=Output_BoostTop_Advance |
| − | CIO Name Of Bend Positive= MOVE_BEND_POS_RELATIVE | + | CIO Name Of Bend Positive=MOVE_BEND_POS_RELATIVE |
CIO Name Of Output Machine Lube=Output_MachineLube_Repeat | CIO Name Of Output Machine Lube=Output_MachineLube_Repeat | ||
| + | CIO Name of Input Machine Lube Complete=Input_MachineLubeComplete_End | ||
| + | CIO Name Of Output Bend Head Down1=Output_HeadShiftDown1_Repeat | ||
| + | CIO Name Of Output Bend Head Down2=Output_HeadShiftDown2_Repeat | ||
| + | CIO Name Of Output Bend Head Center1=Output_HeadShiftCenter1_Repeat | ||
| + | CIO Name Of Output Bend Head Center2=Output_HeadShiftCenter2_Repeat | ||
| + | CIO Name Of Output Bend Head Up1=Output_HeadShiftUp1_Repeat | ||
| + | CIO Name Of Output Bend Head Up2=Output_HeadShiftUp2_Repeat | ||
| Line 43: | Line 51: | ||
AM=auto_mode.wav | AM=auto_mode.wav | ||
SMMF=switch_to_manual_mode_first.wav | SMMF=switch_to_manual_mode_first.wav | ||
| + | |||
| + | [Loop] | ||
| + | Power Off Manual Mode Pause=5 | ||
| + | Power On Manual Mode Pause=5 | ||
| + | Cycle Hold Pause=5 | ||
| + | |||
| + | [Opcode] | ||
| + | Transform 2031 Enabled=0 | ||
| + | Transformed 2031=2023 | ||
[PRIORITY] | [PRIORITY] | ||
Revision as of 20:54, 28 January 2009
Contents |
What is It?
The CNCProcessor.cfg file exists in the c:\cnc\config folder. It contains setup information for the CNC Processor.
Sections
Each of the sections in the CNCProcessor.cfg is set apart with values in square brackets like this:
[Machine Lube]
Properties for Older Versions of CNC Bender
Example properties for an axis:
[Machine Lube] Machine Lube Duration=5000 Lube Machine At Bend Count=100 Pulse Machine Lube Pump=1 Watch For Machine Lube Complete Input=0 [CIO] CIO Name Of Input Clamp Die Close=Input_ClampIsClosed_End CIO Name Of Input Pressure Die Home=Input_PressureDieIsHome_End CIO Name Of Input Pressure Die Close=Input_PressureDieIsClosed_End CIO Name Of Input Carriage Cross Slide Advance=Input_CarriageCrossSlideIsAdvanced_End CIO Name Of Input Release Button=Input_Release_Button_End CIO Name Of Output Release Illuminate=Output_Release_Illuminate CIO Name Of Boost Bottom Advance=Output_BoostBottom_Advance CIO Name Of Boost Top Advance=Output_BoostTop_Advance CIO Name Of Bend Positive=MOVE_BEND_POS_RELATIVE CIO Name Of Output Machine Lube=Output_MachineLube_Repeat CIO Name of Input Machine Lube Complete=Input_MachineLubeComplete_End CIO Name Of Output Bend Head Down1=Output_HeadShiftDown1_Repeat CIO Name Of Output Bend Head Down2=Output_HeadShiftDown2_Repeat CIO Name Of Output Bend Head Center1=Output_HeadShiftCenter1_Repeat CIO Name Of Output Bend Head Center2=Output_HeadShiftCenter2_Repeat CIO Name Of Output Bend Head Up1=Output_HeadShiftUp1_Repeat CIO Name Of Output Bend Head Up2=Output_HeadShiftUp2_Repeat [SOUND] INIT=cncbender_initialized.wav AE=all_axes_enabled.wav AD=all_axes_disabled.wav WRE=warning_range_error_encountered.wav CH=cycle_hold.wav CS=cycle_start.wav MM=manual_mode.wav SM=step_mode.wav AM=auto_mode.wav SMMF=switch_to_manual_mode_first.wav [Loop] Power Off Manual Mode Pause=5 Power On Manual Mode Pause=5 Cycle Hold Pause=5 [Opcode] Transform 2031 Enabled=0 Transformed 2031=2023 [PRIORITY] Master Loop Priority=10000
Note that remarks may be added to the file with lines preceded by double forward slashes.
// How long does the machine loop output enable?
Properties Definition
Read about individual properties:
These two properties control the Auto Lube feature:
Machine Lube Duration
Lube Machine At Bend Count
