Difference between revisions of "CNC Bender v12-20100414"
From ATTWiki
| (9 intermediate revisions by one user not shown) | |||
| Line 5: | Line 5: | ||
<br> | <br> | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
</td> | </td> | ||
<td> | <td> | ||
| − | + | [[image:v12mainmenu.jpg|400px]] | |
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| + | __TOC__ | ||
| + | |||
| + | |||
| + | ===[[image:Check.jpg|25px]] ENHANCED - Benderlink Changes START Position Adjustment=== | ||
| + | <table> | ||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | Benderlink is enhanced to correctly change the START position of the carriage during correction if that feature is switched on. | ||
| + | </td> | ||
| + | <td> | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
</td> | </td> | ||
<td> | <td> | ||
| − | |||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | + | ===[[image:Check.jpg|25px]] REPAIRED - Benderlink Database Transfer Setup Clear=== | |
| − | + | ||
| − | + | ||
| − | ===[[image:Check.jpg|25px]] REPAIRED - Benderlink Database Transfer=== | + | |
<table> | <table> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
The CNC Bender database was corrupted when Benderlink users pressed the "Apply and Close" button without first having made a correction. The result was a CNC Bender setup that would cause major issues in CNC Bender.<br><br> | The CNC Bender database was corrupted when Benderlink users pressed the "Apply and Close" button without first having made a correction. The result was a CNC Bender setup that would cause major issues in CNC Bender.<br><br> | ||
| − | This issue has been corrected by automatically updating the Adjusted database when Benderlink shows on the screen. There is no possibility that the the setup database can now be cleared | + | This issue has been corrected by automatically updating the Adjusted database when Benderlink shows on the screen. There is no possibility that the the setup database can now be cleared improperly. |
</td> | </td> | ||
<td> | <td> | ||
| Line 72: | Line 81: | ||
If the Immediate Message box displays while an operator is pressing a JOG+ or JOG- button in direct axes jog mode, then CNC Bender would never allow the jog button to come up. This has been resolved. | If the Immediate Message box displays while an operator is pressing a JOG+ or JOG- button in direct axes jog mode, then CNC Bender would never allow the jog button to come up. This has been resolved. | ||
</td> | </td> | ||
| + | <td> | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | </td> | ||
| + | <td> | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] REPAIRED - Automatic Feed Adjustment During Part Load=== | ||
| + | <table> | ||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | The automatic feed adjustment feature works by advising operators that incoming part data was from another bender with a different bed length. We discovered that two of the Tool page options were not being changed properly. This is corrected.</td> | ||
<td> | <td> | ||
</td> | </td> | ||
Latest revision as of 14:28, 16 April 2010
|
|
|
Contents |
ENHANCED - Benderlink Changes START Position Adjustment
|
Benderlink is enhanced to correctly change the START position of the carriage during correction if that feature is switched on. |
|
REPAIRED - Benderlink Database Transfer Setup Clear
|
The CNC Bender database was corrupted when Benderlink users pressed the "Apply and Close" button without first having made a correction. The result was a CNC Bender setup that would cause major issues in CNC Bender. |
|
REPAIRED - Single Radius Carriage Shifting
|
Single radius carriage shifting is now re-enabled in this version. |
|
REPAIRED - Direct Axes Jog Buttons Stick Down
|
If the Immediate Message box displays while an operator is pressing a JOG+ or JOG- button in direct axes jog mode, then CNC Bender would never allow the jog button to come up. This has been resolved. |
|
REPAIRED - Automatic Feed Adjustment During Part Load
| The automatic feed adjustment feature works by advising operators that incoming part data was from another bender with a different bed length. We discovered that two of the Tool page options were not being changed properly. This is corrected. | |
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
