Difference between revisions of "Benderlink for FARO 1.5"
From ATTWiki
| (21 intermediate revisions by one user not shown) | |||
| Line 6: | Line 6: | ||
| − | ===[[image:Check.jpg|25px]] New - | + | |
| + | ===[[image:Check.jpg|25px]] New - Reverse Bend Data Features === | ||
| + | |||
| + | |||
<table> | <table> | ||
<tr> | <tr> | ||
| − | <td width= | + | <td width=550> |
| + | There are times when the nominal tube data may show the opposite point and bend order than used for bending. During communications, the bend order needs to be the same - so this allows operators to adjust the order of the bend data to fit both the CAM2 measure and the bend data setup in the bender control.<br> | ||
| + | <br> | ||
| + | </td> | ||
| + | <td> | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] New - Automatically Reverse Incoming Data Checkbox === | ||
| + | |||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=150> | ||
Benderlink can now automatically reverse all incoming FARO CAM2 data if this new feature is enabled. | Benderlink can now automatically reverse all incoming FARO CAM2 data if this new feature is enabled. | ||
</td> | </td> | ||
<td> | <td> | ||
| − | [[image:blinkfaro_autoreversefeature.jpg| | + | [[image:blinkfaro_autoreversefeature.jpg|350px]] |
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| + | <br><br> | ||
| + | ===[[image:Check.jpg|25px]] New - Reverse Bender Data or Un-reverse Bender Data=== | ||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=150> | ||
| + | Benderlink can now reverse the FARO CAM2 data after it is imported. The Reverse Bend Data button acts as a toggle for reversing and un-reversing the bend data. | ||
| + | <br><br> | ||
| + | The new "Data Original" or "Data Reverse" flag also clearly shows if the data has been reversed. | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:blinkfaro_reversefeature.jpg|350px]]<br><br> | ||
| − | + | [[image:blinkfaro_reverseflag.jpg|350px]] | |
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | <br><br> | ||
| − | + | ===[[image:Check.jpg|25px]] New - 64 Bit Compatibility === | |
| − | + | This Benderlink is now compatible with 64 bit Windows | |
<br><br> | <br><br> | ||
| − | ===[[image:Check.jpg|25px]] New - | + | ===[[image:Check.jpg|25px]] New - AddisonMckee Control Compatibility === |
<table> | <table> | ||
<tr> | <tr> | ||
<td width=150> | <td width=150> | ||
| − | Benderlink now | + | Benderlink for FARO now has extended Supravision network capabilities for AddisonMckee Mark IV and Mark V controls.</td> |
<td> | <td> | ||
| − | [[image: | + | [[image:addison_databend.jpg|300px]] |
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] Fix - User Interface Memory Leaks Repaired === |
<table> | <table> | ||
<tr> | <tr> | ||
| − | <td width= | + | <td width=550> |
| − | Benderlink now | + | Benderlink caused resource failures in previous versions. This has been resolved with this version of Benderlink for FARO.</td> |
| + | <td> | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | <br> | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] New - Screen Snap === | ||
| + | |||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=550> | ||
| + | Benderlink now has screen snap capability. As you move Benderlink toward the screen edge, the window will snap to the edge of the screen.</td> | ||
<td> | <td> | ||
| − | |||
</td> | </td> | ||
</tr> | </tr> | ||
Latest revision as of 15:35, 23 July 2010
New - Reverse Bend Data Features
|
There are times when the nominal tube data may show the opposite point and bend order than used for bending. During communications, the bend order needs to be the same - so this allows operators to adjust the order of the bend data to fit both the CAM2 measure and the bend data setup in the bender control. |
New - Automatically Reverse Incoming Data Checkbox
|
Benderlink can now automatically reverse all incoming FARO CAM2 data if this new feature is enabled. |
|
New - Reverse Bender Data or Un-reverse Bender Data
|
Benderlink can now reverse the FARO CAM2 data after it is imported. The Reverse Bend Data button acts as a toggle for reversing and un-reversing the bend data.
|
|
New - 64 Bit Compatibility
This Benderlink is now compatible with 64 bit Windows
New - AddisonMckee Control Compatibility
| Benderlink for FARO now has extended Supravision network capabilities for AddisonMckee Mark IV and Mark V controls. |
|
Fix - User Interface Memory Leaks Repaired
| Benderlink caused resource failures in previous versions. This has been resolved with this version of Benderlink for FARO. |
New - Screen Snap
| Benderlink now has screen snap capability. As you move Benderlink toward the screen edge, the window will snap to the edge of the screen. |
Other Pages
- Back to the Benderlink for FARO page
