Difference between revisions of "DOCS2Addison Benderlink"
From ATTWiki
(→RUN Screen) |
|||
| (26 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
| + | [[image:docs2addison_logo.jpg|400px]] | ||
<table> | <table> | ||
| + | |||
<tr> | <tr> | ||
| − | <td>[[ | + | <td width=300>DOCS2Addison Benderlink is software is designed to allow the [[AddisonMckee]] to communicate with the [[DOCS]]-based measuring center.<br><br> |
| − | <td>[[image: | + | </td> |
| + | <td>[[image:docs2addison_mainscreen_run.jpg|thumb|DOCS2Addison Run Screen]]</td> | ||
</tr> | </tr> | ||
| + | |||
| + | <tr> | ||
| + | <td width=300>[[image:addison_databend.jpg|200px]] | ||
| + | </td> | ||
| + | <td>[[image:romer_infinite.jpg|200px]]</td> | ||
| + | </tr> | ||
| + | |||
</table> | </table> | ||
| − | |||
| + | ==SETUP Screen == | ||
| + | |||
| + | <table> | ||
| + | |||
| + | <tr> | ||
| + | <td width=300>This is where all setup occurs in Benderlink. Up to 100 benders can be programmed and '''remembered'' in this Benderlink. <br><br> | ||
| + | </td> | ||
| + | <td>[[image:docs2addison_mainscreen_setup.jpg|400px]]</td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | |||
| + | ==RUN Screen== | ||
| + | |||
| + | <table> | ||
| + | |||
| + | <tr> | ||
| + | <td width=300>This is the screen where Benderlinking occurs. Choose the bender number in the Setup screen, then switch to RUN. <br><br> | ||
| + | Benderlink has two modes for AddisonMckee: NEW and CORRECTION. The two buttons on this screen let you choose one of the two modes. NEW is for sending new data to establish the part the first time. CORRECTION is for sending correction data to the bender. (AddisonMckee makes a distinction between the two.) | ||
| + | |||
| + | </td> | ||
| + | <td>[[image:docs2addison_mainscreen_run.jpg|400px]]</td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | |||
| + | ==Other Pages== | ||
| − | [[ | + | * Back to [[Benderlink]] |
Latest revision as of 03:51, 30 July 2010
| DOCS2Addison Benderlink is software is designed to allow the AddisonMckee to communicate with the DOCS-based measuring center. |
 |
|
 |
SETUP Screen
| This is where all setup occurs in Benderlink. Up to 100 benders can be programmed and 'remembered in this Benderlink. |
 |
RUN Screen
| This is the screen where Benderlinking occurs. Choose the bender number in the Setup screen, then switch to RUN. Benderlink has two modes for AddisonMckee: NEW and CORRECTION. The two buttons on this screen let you choose one of the two modes. NEW is for sending new data to establish the part the first time. CORRECTION is for sending correction data to the bender. (AddisonMckee makes a distinction between the two.) |
|
Other Pages
- Back to Benderlink
