Difference between revisions of "CNC Bender v12-20110212"
From ATTWiki
| (19 intermediate revisions by one user not shown) | |||
| Line 2: | Line 2: | ||
<tr> | <tr> | ||
<td width=200> | <td width=200> | ||
| − | ==v12- | + | ==v12-20110212== |
*Back to [[CNC Bender Software Updates]] | *Back to [[CNC Bender Software Updates]] | ||
</td> | </td> | ||
| Line 15: | Line 15: | ||
__NOTOC__ | __NOTOC__ | ||
| − | ===[[image:Check.jpg|25px]] ENHANCEMENTS - | + | ===[[image:Check.jpg|25px]] ENHANCEMENTS - New Option Visibility Control for OEMs === |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | * OEMs now have option list control that is protected by encryption.<br><br> | + | * OEMs now have option list control that is protected by encryption. Any list option can be switched off by the OEM during machine setup.<br><br> |
| − | * Push | + | * Push Bend Allow and PDA-RVG Allow no longer switch on automatically in the general dynamic options list if a license for either option is found in the hardware key. Only the setup technician can enable or disable these values in the Low Level menu of CNC Bender ProControl. |
| − | <br> | + | <br><br> |
| + | </td> | ||
| + | |||
| + | <td> | ||
| + | [[image:cncbender_dynamicoptionlistcontrol.jpg|400px]] | ||
| + | </td> | ||
| + | |||
| + | </tr> | ||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] ENHANCEMENTS - New Message in Splash === | ||
| + | |||
| + | <table cellpadding=10> | ||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | * If the CNC Bender Options Visibility configuration file is not present, then CNC Bender will not load.<br><br> | ||
| + | * The splash screen will show this message:<br><br> | ||
| + | </td> | ||
| + | |||
| + | <td> | ||
| + | [[image:cncbender_splash_nooptionvisibilityfile.jpg|400px]] | ||
| + | </td> | ||
| + | |||
| + | </tr> | ||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | |||
| + | |||
| + | ===[[image:Check.jpg|25px]] Other Changes === | ||
| + | |||
| + | <table cellpadding=10> | ||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | * The '''CNCBenderDOD.cfg''' filename is changed to '''DynamicOptionVisibility.cfg''' in order to better reflect the purpose of the file. | ||
</td> | </td> | ||
<td> | <td> | ||
| − | |||
</td> | </td> | ||
Latest revision as of 18:38, 14 February 2011
v12-20110212
|
|
ENHANCEMENTS - New Option Visibility Control for OEMs
|
|
ENHANCEMENTS - New Message in Splash
|
|
Other Changes
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
