Difference between revisions of "Main.axislist"
From ATTWiki
| (19 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
| + | [[image:cncbender_logo.jpg|400px]] | ||
| + | __notoc__ | ||
| + | <table cellpadding="5"> | ||
| + | <tr><td width=25></td> | ||
| + | <td width=300 bgcolor="#f0f0f0"> | ||
| + | <font size=5>[[image:Gear_warning.jpg]] <b>WARNING</b><br><br></font> | ||
| + | <font size=3>This information is highly technical and it is not exhaustive.<br><br>Please '''DO NOT''' make experimental changes to this file unless you know exactly how each variable affects the operation of CNC Bender.<br><br> | ||
| + | If you have a doubt, then please ask us first.</font></td></tr></table> | ||
| + | |||
===What is It?=== | ===What is It?=== | ||
The main.axislist file exists in the c:\cnc\config\axis folder. It contains setup information for each of the controlled axes on a CNC bender. | The main.axislist file exists in the c:\cnc\config\axis folder. It contains setup information for each of the controlled axes on a CNC bender. | ||
| − | === | + | ===Sections=== |
| − | + | Each of the sections in the main.axislist is set apart with an axis section label like this: | |
| − | + | ||
| + | <pre>[Axis 1]</pre> | ||
| + | |||
| + | Each section has individual properties that pertain to that axis. | ||
| + | |||
| + | |||
| + | ===Properties=== | ||
| + | Example properties for an axis: | ||
| + | <pre> | ||
| + | [Axis 1] | ||
| + | Type=Feed | ||
| + | Module Name=servo_controller_module_1 | ||
| + | Module Axis=1 | ||
| + | Position Multiplier For Display= 1.0 | ||
| + | Position Rollover= 32000 | ||
| + | Position Rollover Tolerance= 100 | ||
| + | // Move Feed Axis forward 0.25 forward and make that ZERO | ||
| + | // This prevents ever getting into slight negative region | ||
| + | // which causes rollover problems. | ||
| + | Position Offset=0.25 | ||
| + | Position Offset Speed=400 | ||
| + | Datum Offset=0 | ||
| + | Home Required=1 | ||
| + | Monitor Fault State=1 | ||
| + | Monitor Enable State=1 | ||
| + | Monitor In-Position State=0 | ||
| + | // 1 = -10 to +10 volts | ||
| + | Analog Clamp Voltage Setup=1 | ||
| + | Digital To Analog Datum=8191 | ||
| + | Is Linear = 1 | ||
| + | Delay After Cycle Start = 0 | ||
| + | Dont Move If Position Within Tolerance Value = 0.5 | ||
| + | </pre> | ||
| + | Note that remarks may be added to the file with lines preceded by double forward slashes. | ||
| − | + | <pre>// Move Feed Axis forward 0.25 forward and make that ZERO</pre> | |
Latest revision as of 19:00, 3 November 2007
|
|
What is It?
The main.axislist file exists in the c:\cnc\config\axis folder. It contains setup information for each of the controlled axes on a CNC bender.
Sections
Each of the sections in the main.axislist is set apart with an axis section label like this:
[Axis 1]
Each section has individual properties that pertain to that axis.
Properties
Example properties for an axis:
[Axis 1] Type=Feed Module Name=servo_controller_module_1 Module Axis=1 Position Multiplier For Display= 1.0 Position Rollover= 32000 Position Rollover Tolerance= 100 // Move Feed Axis forward 0.25 forward and make that ZERO // This prevents ever getting into slight negative region // which causes rollover problems. Position Offset=0.25 Position Offset Speed=400 Datum Offset=0 Home Required=1 Monitor Fault State=1 Monitor Enable State=1 Monitor In-Position State=0 // 1 = -10 to +10 volts Analog Clamp Voltage Setup=1 Digital To Analog Datum=8191 Is Linear = 1 Delay After Cycle Start = 0 Dont Move If Position Within Tolerance Value = 0.5
Note that remarks may be added to the file with lines preceded by double forward slashes.
// Move Feed Axis forward 0.25 forward and make that ZERO
