Difference between revisions of "CNC Bender v12-20120622"

From ATTWiki
Jump to: navigation, search
(→‎25px New - Horizontal Axis LOAD Position in PREBEND)
(→‎25px Enhancement - AutoSleep Removed)
 
(4 intermediate revisions by one user not shown)
Line 13: Line 13:
 
</table>
 
</table>
 
__NOTOC__
 
__NOTOC__
−
===[[image:Check.jpg|25px]] Repair - Recovery Mode Rotate Spin 180===
+
 
 +
 
 +
===[[image:Check.jpg|25px]] New - Radius Level for LOAD Position in PREBEND===
  
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=400>
 
<td width=400>
−
The ROTATE axis could incorrectly rotate 360 degrees when recovering from safety mat activation under rare circumstances of the rotate drifting way from zero.  This has been fixed.
+
The new option "Radius Level for Loading" shows a list composed of 5 options for controlling where the carriage is vertically during LOADING the part.   These are the five options:<br>
 
<br>
 
<br>
 +
#Use the Radius from the first FRB Row
 +
#Use Radius level 1
 +
#Use Radius level 2
 +
#Use Radius level 3
 +
#Use Radius level 4
 +
 
</td>
 
</td>
  
Line 29: Line 37:
 
</table>
 
</table>
  
 +
[[image:cncbender_radiuslevel_for_loading.jpg]]
  
−
===[[image:Check.jpg|25px]] Repair - Robot Clear Bit Can Be High or Low===
+
===[[image:Check.jpg|25px]] New - Horizontal Axis LOAD Position in PREBEND===
  
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=400>
 
<td width=400>
−
The Robot Clear bit always assumed that the TRUE signal was bit high.  But some machines assume the opposite.  This has been fixed.
+
A new option allows the horizontal axis to move to a specific position for loading.  This is a two-option feature:<br>
 +
</td>
 +
 
 +
<td width=300>
 +
</td>
 +
 
 +
</tr>
 +
</table>
 +
[[image:cncbender_horizontalaxisloadposition.jpg]]
 +
 
 +
===[[image:Check.jpg|25px]] Repair - Recovery Mode Rotate Spin 180===
 +
 
 +
<table cellpadding=10>
 +
<tr valign=top>
 +
<td width=400>
 +
The ROTATE axis could incorrectly rotate 360 degrees when recovering from safety mat activation under rare circumstances of the rotate drifting way from zero.  This has been fixed.
 
<br>
 
<br>
 
</td>
 
</td>
Line 47: Line 71:
  
  
−
===[[image:Check.jpg|25px]] New - Radius Level for LOAD Position in PREBEND===
+
===[[image:Check.jpg|25px]] Repair - Robot Clear Bit Can Be High or Low===
  
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=400>
 
<td width=400>
−
The new option "Radius Level for Loading" shows a list composed of 5 options for controlling where the carriage is vertically during LOADING the part.   These are the five options:<br>
+
The Robot Clear bit always assumed that the TRUE signal was bit high. But some machines assume the opposite.  This has been fixed.
 
<br>
 
<br>
−
#Use the Radius from the first FRB Row
 
−
#Use Radius level 1
 
−
#Use Radius level 2
 
−
#Use Radius level 3
 
−
#Use Radius level 4
 
−
 
 
</td>
 
</td>
  
Line 69: Line 87:
 
</table>
 
</table>
  
−
 
+
===[[image:Check.jpg|25px]] Enhancement - AutoSleep Removed===
−
===[[image:Check.jpg|25px]] New - Horizontal Axis LOAD Position in PREBEND===
+
  
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=400>
 
<td width=400>
−
A new option allows the horizontal axis to move to a specific position for loading.  This is a two-option feature:<br>
+
Since CNC Processor is now highly optimized, the AutoSleep feature, where the CNC Bender user interface could be put to sleep to decrease delay between steps, is no longer needed.<br>
 +
<br>
 +
Now the CNC Processor runs fast with our without AutoSleep enabled.
 
</td>
 
</td>
  
 
<td width=300>
 
<td width=300>
 +
 
</td>
 
</td>
  
 
</tr>
 
</tr>
 
</table>
 
</table>
−
[[image:cncbender_horizontalaxisloadposition.jpg]]
 
  
 
=Other Pages=
 
=Other Pages=

Latest revision as of 01:31, 30 June 2012

v12-20120622

Cncv12procontrol withteachmode.jpg


Check.jpg New - Radius Level for LOAD Position in PREBEND

The new option "Radius Level for Loading" shows a list composed of 5 options for controlling where the carriage is vertically during LOADING the part. These are the five options:

  1. Use the Radius from the first FRB Row
  2. Use Radius level 1
  3. Use Radius level 2
  4. Use Radius level 3
  5. Use Radius level 4

Cncbender radiuslevel for loading.jpg

Check.jpg New - Horizontal Axis LOAD Position in PREBEND

A new option allows the horizontal axis to move to a specific position for loading. This is a two-option feature:

Cncbender horizontalaxisloadposition.jpg

Check.jpg Repair - Recovery Mode Rotate Spin 180

The ROTATE axis could incorrectly rotate 360 degrees when recovering from safety mat activation under rare circumstances of the rotate drifting way from zero. This has been fixed.


Check.jpg Repair - Robot Clear Bit Can Be High or Low

The Robot Clear bit always assumed that the TRUE signal was bit high. But some machines assume the opposite. This has been fixed.

Check.jpg Enhancement - AutoSleep Removed

Since CNC Processor is now highly optimized, the AutoSleep feature, where the CNC Bender user interface could be put to sleep to decrease delay between steps, is no longer needed.

Now the CNC Processor runs fast with our without AutoSleep enabled.

Other Pages

Retrieved from "http://www.advancedtubular.wiki/index.php?title=CNC_Bender_v12-20120622&oldid=18480"