Difference between revisions of "VTube-LASER v1.78"
(→Other Pages) |
|||
| (33 intermediate revisions by one user not shown) | |||
| Line 10: | Line 10: | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | [[image:Vtube-laser_1. | + | [[image:Vtube-laser_1.78.jpg|300px]] |
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | + | __NOTOC__ | |
* See [http://www.advancedtubular.com/customers/vtube VTube-LASER Customer Support Page] to download the latest version. | * See [http://www.advancedtubular.com/customers/vtube VTube-LASER Customer Support Page] to download the latest version. | ||
| − | + | ==[[image:Check.jpg|25px]] NEW: Bender Data Output with Full Springback== | |
| + | |||
| + | ===1 - Bender Communiciation with Full Springback=== | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | + | Full springback is now included in direct communications with benders connected to the bender network in VTube. This data responds to the Fixed and Proportional springback values in the Part Setup menu. | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | The benefit of this feature is that you can include springback in the original master data for first-time setup of the bender. | |
| − | + | ''Note: This feature is accessed from VTube-STEP mode which is included in the VTube-LASER license.'' | |
| − | + | ||
| − | + | ||
| − | + | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| + | [[image:vtube-laser_springbackoutput_communication_v1.78.jpg|300px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | + | ===2 - Reports can Output LRA with Full Springback=== | |
| − | + | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| + | Full springback can now be printed in the reports for first-time setup of benders. This report responds to the Fixed and Proportional springback values in the Part Setup menu. | ||
| + | |||
This feature also includes the added report tags that allow for the values with springback to be placed anywhere in the report: | This feature also includes the added report tags that allow for the values with springback to be placed anywhere in the report: | ||
| Line 65: | Line 59: | ||
</td> | </td> | ||
| + | |||
<td width=300> | <td width=300> | ||
| + | [[image:vtube-laser_springbackreport_v1.78.jpg|300px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | + | ===3 - Bender Files Output LRA with Full Springback=== | |
| − | + | ||
| − | + | ||
| − | === | + | |
| Line 80: | Line 73: | ||
<td width=400> | <td width=400> | ||
Full springback is now included in the export of bender files in all formats. This data responds to the Fixed and Proportional springback values in the Part Setup menu. | Full springback is now included in the export of bender files in all formats. This data responds to the Fixed and Proportional springback values in the Part Setup menu. | ||
| + | |||
| + | ''Note: This feature is accessed from VTube-STEP mode which is included in the VTube-LASER license.'' | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| + | [[image:vtube-laser_springbackoutput_v1.78.jpg|300px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | [[image: | + | ==[[image:Check.jpg|25px]] NEW: "Supplier" Field in Part Setup== |
| − | + | ||
| − | + | ||
| − | ===[[image:Check.jpg|25px]] NEW: IMPORT Template Feature in Report Menu | + | <table cellpadding=10> |
| + | <tr valign=top> | ||
| + | <td width=400> | ||
| + | Some of our customers receive parts from suppliers, so we've added a "Supplier" field in the Part Setup menu. | ||
| + | |||
| + | This data is saved in the project files. | ||
| + | |||
| + | |||
| + | This feature also includes the added report tags that allow for the values with springback to be placed anywhere in the report: | ||
| + | |||
| + | * "Supplier" | ||
| + | |||
| + | |||
| + | And it is used in a report template like this: | ||
| + | |||
| + | <pre> | ||
| + | <vtube_val>Supplier</vtube_val> | ||
| + | </pre> | ||
| + | |||
| + | </td> | ||
| + | <td width=300> | ||
| + | [[image:vtube-laser_supplierfield_v1.78.jpg|300px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | ==[[image:Check.jpg|25px]] NEW: IMPORT Template Feature in Report Menu== | ||
| Line 101: | Line 121: | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| + | [[image:vtube-laser_importreporttemplate_v1.78.jpg|300px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | |||
| − | |||
| − | + | ==[[image:Check.jpg|25px]] ENHANCED: New Master XYZ Pop-Up Menu Commands== | |
| Line 119: | Line 138: | ||
* Additive invert the entire selected column (for mirror imaging) | * Additive invert the entire selected column (for mirror imaging) | ||
| + | [[image:vtube-laser_mirror_image_additive_inverse.jpg|300px]] | ||
</td> | </td> | ||
| Line 126: | Line 146: | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | |||
| − | |||
| − | |||
| − | + | ==[[image:Check.jpg|25px]] ENHANCED: New Measured XYZ Pop-Up Menu Commands== | |
<table cellpadding=10> | <table cellpadding=10> | ||
| Line 148: | Line 165: | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | |||
| − | |||
| − | |||
==Other Pages== | ==Other Pages== | ||
Latest revision as of 00:14, 6 October 2012
|
Revision 1.78
|
|
- See VTube-LASER Customer Support Page to download the latest version.
NEW: Bender Data Output with Full Springback
1 - Bender Communiciation with Full Springback
|
Full springback is now included in direct communications with benders connected to the bender network in VTube. This data responds to the Fixed and Proportional springback values in the Part Setup menu. The benefit of this feature is that you can include springback in the original master data for first-time setup of the bender. Note: This feature is accessed from VTube-STEP mode which is included in the VTube-LASER license. |
|
2 - Reports can Output LRA with Full Springback
|
Full springback can now be printed in the reports for first-time setup of benders. This report responds to the Fixed and Proportional springback values in the Part Setup menu. This feature also includes the added report tags that allow for the values with springback to be placed anywhere in the report:
And they are used in a report template like this: <vtube_val>Array_L_FullSpringback</vtube_val> |
|
3 - Bender Files Output LRA with Full Springback
|
Full springback is now included in the export of bender files in all formats. This data responds to the Fixed and Proportional springback values in the Part Setup menu. Note: This feature is accessed from VTube-STEP mode which is included in the VTube-LASER license. |
|
NEW: "Supplier" Field in Part Setup
|
Some of our customers receive parts from suppliers, so we've added a "Supplier" field in the Part Setup menu. This data is saved in the project files.
<vtube_val>Supplier</vtube_val> |
|
NEW: IMPORT Template Feature in Report Menu
|
The report menu was reorganized and an IMPORT feature was added to simplify the import of REPORT TEMPLATES into your VTube system. Choose the html report to import, and VTube automatically copies it into the system and adds it to the template list. |
|
ENHANCED: New Master XYZ Pop-Up Menu Commands
|
New features in the XYZ pop-up menu adds new commands.
|
|
ENHANCED: New Measured XYZ Pop-Up Menu Commands
|
New features in the XYZ pop-up menu adds new commands.
|
|
Other Pages
- Back to the VTube-LASER page
- See VTube-LASER Customer Support Page to download the latest version.
