Difference between revisions of "VTube-LASER Bender Corrections"
From ATTWiki
(Created page with "<table> <tr cellpadding=10> <td width=300> 300px *Back to VTube-LASER *Back to VTube-STEP </td> <td width=300> image:Vtube-laser_1.77...") |
(→"Bidirectional Communication" - FOR CORRECTIONS) |
||
| (58 intermediate revisions by one user not shown) | |||
| Line 16: | Line 16: | ||
__TOC__ | __TOC__ | ||
| + | ==Correcting a Bender== | ||
| − | == | + | <table> |
| + | <tr> | ||
| + | <td width=300> | ||
| + | You can see the deviation in this part. The transparent yellow tolerance envelopes indicate that the part is outside of the deviation tolerance allowed (in this case 0.039" or 1 mm).<br><br> | ||
| + | VTube-LASER can send correction data to benders to steer them into the correction motion to make the correct tube shape. | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:vtube-laser_tubemodel_aligned_demo0625.jpg|500px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | |||
| + | |||
| + | ==BENDER SETUP Window== | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | VTube-LASER uses the Bender Setup screen to control the values in connected benders. | + | |
| + | VTube-LASER uses the Bender Setup screen to control the values in up to 100 connected benders.<br><br> | ||
| + | This screen shows data that is a separate part of VTube memory. The data in this screen is the bender data, both before and after correction, and it is kept unchanged unless changed by the operator.<br><br> | ||
| + | |||
| + | * The blue columns represent the data at the bender before correction.<br><br> | ||
| + | * The orange columns represent the data at the bender after correction.<br><br> | ||
| + | * The columns between the blue and orange columns represent the adjustments to the data. | ||
| + | |||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | [[image:vtube-laser-bendersetup_screen.jpg]] | + | |
| + | [[image:vtube-laser-bendersetup_screen.jpg|500px]]<br> | ||
| + | [[image:vtube-laser-bendersetup_grid.jpg|500px]] | ||
| + | |||
</td> | </td> | ||
</tr> | </tr> | ||
| + | </table> | ||
| + | =="Setup the Bender" - FOR SENDING NEW DATA== | ||
| + | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | + | Use the "SETUP THE BENDER" section on the right to send new data.<br><br> | |
| − | + | VTube-LASER can also send setup data to the bender for setup.<br><br> | |
| − | <br><br> | + | The software has several choices for controlling how the data is formatted before sending to the bender. |
| − | + | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | [[image:vtube- | + | [[image:vtube-laser-bendersetup_newdata.jpg|400px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| + | </table> | ||
| + | =="Bidirectional Communication" - FOR CORRECTIONS== | ||
| + | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | + | With the right protocol at the bender, VTube-LASER can recall data from the bender, and send both setup and correction data to the bender.<nowiki>*</nowiki><br><br> | |
| − | + | * Operators typically press the "1" button to recall data to be sure the data in the blue columns match the data in the bender.<br><br> | |
| − | + | * Then they press "2" to send the orange columns to the bender as corrected data.<br><br> | |
| − | + | * Press "3" to clear the adjustment data after a correction as it should only be used one time.<br><br> | |
| + | * For benders that can't respond to a recall (1 above), they can recalculate the blue columns by clearing and placing the adjustments back into the blue columns automatically.<br><br> | ||
| + | |||
| + | <nowiki>*</nowiki> Not all protocols require a RECALL before sending CORRECTIONS. | ||
| + | |||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | [[image:vtube- | + | [[image:vtube-laser-bendesetup_bidirectional_commmunication.jpg|400px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| + | </table> | ||
| − | + | ==Correction Damping== | |
| + | <table cellpadding=10> | ||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | VTube-LASER uses a unique correction damping feature for situations were corrections tend to over correct.<br><br> | ||
| + | We learned the damping algorithm by observing customers make manual adjustments to the correction data before sending the data to the bender. | ||
| + | </td> | ||
| + | <td width=300> | ||
| + | [[image:vtube-laser-bendersetup_damping.jpg|500px]] | ||
| + | </td> | ||
| + | </tr> | ||
</table> | </table> | ||
| + | ==Other Pages== | ||
| − | + | * See How to [[Setup VTube for Supravision Network Communication]] | |
| − | + | ||
| − | + | ||
* Back to [[VTube-LASER]] | * Back to [[VTube-LASER]] | ||
Latest revision as of 20:06, 16 July 2018
|
|
|
Contents |
Correcting a Bender
|
You can see the deviation in this part. The transparent yellow tolerance envelopes indicate that the part is outside of the deviation tolerance allowed (in this case 0.039" or 1 mm). |
|
BENDER SETUP Window
|
VTube-LASER uses the Bender Setup screen to control the values in up to 100 connected benders.
|
|
"Setup the Bender" - FOR SENDING NEW DATA
|
Use the "SETUP THE BENDER" section on the right to send new data. |
|
"Bidirectional Communication" - FOR CORRECTIONS
|
With the right protocol at the bender, VTube-LASER can recall data from the bender, and send both setup and correction data to the bender.*
* Not all protocols require a RECALL before sending CORRECTIONS. |
|
Correction Damping
|
VTube-LASER uses a unique correction damping feature for situations were corrections tend to over correct. |
|
Other Pages
- See How to Setup VTube for Supravision Network Communication
- Back to VTube-LASER
