|
|
| (10 intermediate revisions by one user not shown) |
| Line 11: |
Line 11: |
| | </td> | | </td> |
| | <td width=300> | | <td width=300> |
| − | [[image:vtube-step-1.83_screen.png|300px]] | + | [[image:vtube-step-1.84_buildsolidworks.png|300px]] |
| | </td> | | </td> |
| | </tr> | | </tr> |
| Line 47: |
Line 47: |
| | * Build constrained centerline geometry in 3DSketch.<br><br> | | * Build constrained centerline geometry in 3DSketch.<br><br> |
| | [[image:vtube-step-1.84_buildsolidworks.png|400px]]<br> | | [[image:vtube-step-1.84_buildsolidworks.png|400px]]<br> |
| | + | |
| | <br> | | <br> |
| | </td> | | </td> |
| Line 55: |
Line 56: |
| | </table> | | </table> |
| | <br><br> | | <br><br> |
| − |
| |
| − | ===[[image:Check.jpg|25px]] FIX: Supravision Export of End Offsets===
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=400>
| |
| − | The Supravision export would use the A-End and B-End Solid Model Offset for the Supravision end offsets in the exported Supravision file. The values that should be used are the <b>A-End and B-End Length Adjust</b> - because that is the equivalent for Supravision end offsets.<br><br>
| |
| − | This has been repaired in this version.
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − |
| |
| − |
| |
| − | ===[[image:Check.jpg|25px]] NEW: Toolbar "Close" Button===
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=400>
| |
| − | The new Close button allows you to close VTube more quickly than before.<br><br>
| |
| − | [[image:vtube-step-1.83-toolbar_door.png|300px]]
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | [[image:vtube-step-1.83-toolbar_door_closeup.png]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − | <br><br>
| |
| − |
| |
| − | ===[[image:Check.jpg|25px]] NEW: Toolbar "Save As" Button===
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=400>
| |
| − | The new Save As button allows you to save the current part as a new part file.<br><br>
| |
| − | [[image:vtube-step-1.83_saveas_toolbar_button.png|300px]]
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | [[image:vtube-step-1.83-toolbar_saveas_closeup.png|300px]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − | <br><br>
| |
| − |
| |
| − | ===[[image:Check.jpg|25px]] NEW: TubeCalc Elongation Converter ===
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=400>
| |
| − | VTube now includes a TubeCalc Elongation Converter that can be accessed from the Part Setup popup menu. This converter calculates VTube elongation percentages from TubeCalc elongation per degree values.<br><br>
| |
| − | [[image:vtube-1.83-partsetup_popup_menu.png|300px]]
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | [[image:vtube-1.83-tubecalc_elongation_converter.png|300px]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − |
| |
| − | ===[[image:Check.jpg|25px]] NEW: CONRAC Style Bender Chart ===
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=400>
| |
| − | The new chart shows absolute LENGTHS and ROTATIONS appropriate for Conrac style benders.<br><br>
| |
| − | This chart always uses arc lengths that are compensated for elongation based on the elongation percentage in the part setup menu.<br><br>
| |
| − | [[image:vtube-1.83-conracchart.png|500px]]
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| | | | |
| | ===[[image:Check.jpg|25px]] Other Changes=== | | ===[[image:Check.jpg|25px]] Other Changes=== |
| Line 130: |
Line 62: |
| | <td width=400> | | <td width=400> |
| | | | |
| − | * VTube now always reports reduced arc lengths compensated for elongation if the elongation percentage is greater than 0. (It used to always report the theoretical value without elongation.)<br><br> | + | * This version fixes an Overbend memory leak problem that causes an error when the VTube is unloaded in Windows XP.<br><br> |
| − | | + | |
| − | * VTube no longer refreshes the tube model on the screen when a project is saved. This saves significant amount of time for large models.<br><br>
| + | |
| − | | + | |
| − | * The model refresh time is optimized significantly - especially when the point labels are switched on.<br><br>
| + | |
| − | | + | |
| − | * Repairs were made to the Language Editor.<br><br>
| + | |
| − | | + | |
| − | * Internal were made repairs to the Part Setup grid. Corrections were made to field types.<br><br>
| + | |
| − | | + | |
| − | * Click on column cell 1 of the Default Radius field to show the Radius Table.<br><br>
| + | |
| | | | |
| | </td> | | </td> |
NEW: Export to Alpine M4 MBF Data File 
