Difference between revisions of "CNC Bender v12.8"

From ATTWiki
Jump to: navigation, search
(→‎25px FIXED: Teach Mode and Custom Commands Issue Solved)
(→‎25px ENHANCED: Option List Panels Now Clear if no Options Are Present))
 
(3 intermediate revisions by one user not shown)
Line 2: Line 2:
 
<tr>
 
<tr>
 
<td width=400>
 
<td width=400>
−
===v12.8 - February 1, 2014===
+
===v12.8 - February 25, 2014===
 
*Back to [[CNC Bender Software Updates]]
 
*Back to [[CNC Bender Software Updates]]
 
*See [http://advancedtubular.com/customers/cncbender CNC Bender Customer Service Page] for an update.
 
*See [http://advancedtubular.com/customers/cncbender CNC Bender Customer Service Page] for an update.
Line 29: Line 29:
 
* Process list builder now has logic that anticipates that the machine axis number for any motion actuator can change depending on the application.
 
* Process list builder now has logic that anticipates that the machine axis number for any motion actuator can change depending on the application.
  
−
<td width=300>
 
−
</td>
 
 
<td>
 
<td>
 
[[image:smt_handbender.png|400px]]
 
[[image:smt_handbender.png|400px]]
Line 40: Line 38:
 
<br><br>
 
<br><br>
  
−
==[[image:Check.jpg|25px]] ENHANCED: Load and Start Positions with Bend Arm Motion Option (in Pre Bend)==
+
==[[image:Check.jpg|25px]] FIX: Option List Panels Now Clear if no Options Are Present)==
  
 
<table>
 
<table>
 
<tr>
 
<tr>
 
<td width=300>
 
<td width=300>
−
The Option List panels now clear if all options are placed in the tool box.<br><br>
+
</td>
−
 
+
 
<td width=300>
 
<td width=300>
 
[[image:cncbender_OptionPanelCleared.png|600px]]
 
[[image:cncbender_OptionPanelCleared.png|600px]]

Latest revision as of 20:21, 16 July 2014

v12.8 - February 25, 2014

Cncv12procontrol withteachmode.jpg


Check.jpg FIXED: Teach Mode and Custom Commands Issue Solved

If you have a hand-bender controlled by CNC Bender and you use custom commands for the ROTATE axis, then this upgrade is important to you.

Custom commands can be entered after every bend in the FRB page. SMT discovered a that FEED and ROTATE commands would not be completed properly when coming out of a custom move.

  • For example, the ROTATE was programmed at 90 degrees. The custom move is 89 degrees - so the finish up command should be set to 1 degree to come to the full 90. However, the finish-up command was 90 degrees - which caused the rotate to move to 89 + 90 = 179 degrees.

  • This problem occurred on benders where the ROTATE axis is set to a non-standard machine axis 3 because the machine axis number "2" was hard coded into the process list builder.

  • Process list builder now has logic that anticipates that the machine axis number for any motion actuator can change depending on the application.

Smt handbender.png





Check.jpg FIX: Option List Panels Now Clear if no Options Are Present)

Cncbender OptionPanelCleared.png



Check.jpg Other Changes

  • New version number set in all executables: 12.8




Other Pages

Retrieved from "http://www.advancedtubular.wiki/index.php?title=CNC_Bender_v12.8&oldid=24816"