Difference between revisions of "TubeCAD Pro v8-20141217"
From ATTWiki
(→25px REPAIRED - TubeCAD Diameter Outline - Hidden Line Fixes for AutoCAD) |
(→25px ENHANCEMENT - Better Auto Arrange with Assemblies) |
||
| (43 intermediate revisions by one user not shown) | |||
| Line 14: | Line 14: | ||
__NOTOC__ | __NOTOC__ | ||
| − | + | ==[[image:Check.jpg|25px]] FIX- Diameter Outline - Hidden Line Fixes for AutoCAD== | |
<table> | <table> | ||
<tr> | <tr> | ||
| Line 22: | Line 22: | ||
Previous versions of TubeCAD could sometimes draw the hidden lines in the diameter outline on the wrong side of the diameter.<br><br> | Previous versions of TubeCAD could sometimes draw the hidden lines in the diameter outline on the wrong side of the diameter.<br><br> | ||
This has been repaired.<br><br> | This has been repaired.<br><br> | ||
| − | |||
</td> | </td> | ||
<td valign=top> | <td valign=top> | ||
| − | + | [[image:tcadpro_v8-20141217_dxf_hiddenlines_fix.png|500px]] | |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 32: | Line 31: | ||
<br> | <br> | ||
| − | + | ==[[image:Check.jpg|25px]] FIX- 3D Circle Orientation Fix== | |
<table> | <table> | ||
<tr> | <tr> | ||
<td width=300 valign=top> | <td width=300 valign=top> | ||
| − | This version repairs a circle | + | This version repairs a 3D circle orientation problem for certain tube diameters.<br><br> |
All 3D circles are now drawn precisely regardless of their orientation. | All 3D circles are now drawn precisely regardless of their orientation. | ||
</td> | </td> | ||
| Line 45: | Line 44: | ||
</table> | </table> | ||
| − | <br> | + | ==[[image:Check.jpg|25px]] FIX- End To Base Distance Calculations== |
| + | <table> | ||
| + | <tr> | ||
| + | <td width=300 valign=top> | ||
| + | [[image:tcadpro_v8-20141217_blockup_error.png|300px]]<br><br> | ||
| + | The End to Base Blockup label now shows the correct distances.<br><br> | ||
| + | </td> | ||
| + | <td valign=top> | ||
| + | [[image:tcadpro_v8-20141217_blockup_fixed.png|500px]]<br><br> | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| − | + | ==[[image:Check.jpg|25px]] FIX- Artifact Cleanup== | |
<table> | <table> | ||
<tr> | <tr> | ||
<td width=300 valign=top> | <td width=300 valign=top> | ||
| − | + | When changing from a multiple-bend part to a single straight part, TubeCAD would not always cleanup leftover artifacts that no longer apply.<br><br> | |
| + | This has been resolved.<br><br> | ||
| + | </td> | ||
| + | <td valign=top> | ||
| + | [[image:tcadpro_v8-20141217_artifact_cleanup_issue_resolved.png|500px]]<br><br> | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | ==[[image:Check.jpg|25px]] ENHANCEMENTS - Blockup Editor== | ||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=300 valign=top> | ||
| + | * Because each tube view can have its own unique Blockup settings, the Blockup editor screen values now automatically change when you switch active assembly or active view at the top of the window.<br><br> | ||
| + | * The Base Offset for Blockups can now be set in Blockup Editor and stored in the Prototype files - so that the values are setup when you clear TubeCAD. Clear TubeCAD, set the value, then save the file to the correct prototype file. (Get the prototype file name for each unit in the Options pop up menu.)<br><br> | ||
| + | * Now the Individual Blockup Attributes panel is invisible when there are no Blockups on the current view to change. | ||
| + | </td> | ||
| + | <td valign=top> | ||
| + | [[image:tcadpro_v8-20141217_base_offset_setup.png|500px]]<br><br> | ||
| + | [[image:tcadpro_v8-20141217_blockup_editor_individual_blockup_attributes.png|500px]]<br><br> | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | ==[[image:Check.jpg|25px]] ENHANCEMENT - Better Auto Arrange with Assemblies== | ||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=300 valign=top> | ||
| + | * In previous versions, Auto Arrange would not draw the entire layout if some of the tubes were a single straight. Auto Arrange can now properly handle arrangements of assemblies with parts that have a mix of single straight and multi-bend parts.<br><br> | ||
| + | * Auto Arrange automatic spacing was also enhanced for assemblies. | ||
| + | </td> | ||
| + | <td valign=top> | ||
| + | [[image:tcadpro_v8-20141217_assembly_autoarrange.png|500px]]<br><br> | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | ==[[image:Check.jpg|25px]] OTHER== | ||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=400 valign=top> | ||
| + | * TubeCAD now stores all configuration data in the c:\ProgramData\tcadpro folder. This is a folder that is equally shared by all users. Storing files there allows TubeCAD to be setup once for use by all users who log in into Windows with unique credentials. There is no longer any need for setting up TubeCAD for each user like in previous versions.<br><br> | ||
| + | * TubeCAD can now output debug data to Smart Inspect logs and display consoles. This is mainly for testing purposes. | ||
</td> | </td> | ||
<td valign=top> | <td valign=top> | ||
| − | |||
</td> | </td> | ||
</tr> | </tr> | ||
| Line 63: | Line 114: | ||
==Other Pages== | ==Other Pages== | ||
| − | *Customer Support site: Download the upgrade from [http://advancedtubular.com/customers/tubecad | + | *Customer Support site: Download the upgrade from [http://advancedtubular.com/customers/tubecad this page.] |
*Back to the [[TubeCAD Pro]] page | *Back to the [[TubeCAD Pro]] page | ||
Latest revision as of 21:44, 17 December 2014
|
Version 8-20141217Back to TubeCAD Pro |
|
FIX- Diameter Outline - Hidden Line Fixes for AutoCAD
|
|
|
FIX- 3D Circle Orientation Fix
|
This version repairs a 3D circle orientation problem for certain tube diameters. |
|
FIX- End To Base Distance Calculations
|
|
|
FIX- Artifact Cleanup
|
When changing from a multiple-bend part to a single straight part, TubeCAD would not always cleanup leftover artifacts that no longer apply. |
|
ENHANCEMENTS - Blockup Editor
|
|
ENHANCEMENT - Better Auto Arrange with Assemblies
|
|
OTHER
|
Other Pages
- Customer Support site: Download the upgrade from this page.
- Back to the TubeCAD Pro page
