Difference between revisions of "VTube Overbend Calculations for Springback"
(→Built-in Overbend Calculator) |
(→Justification for Using Springback Compensation) |
||
| (42 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
__NOTOC__ | __NOTOC__ | ||
| − | == | + | ==About Overbend Calculator== |
<table> | <table> | ||
| Line 7: | Line 7: | ||
<td width=400 valign="top"> | <td width=400 valign="top"> | ||
| − | The Overbend Calculator is a built-in feature [[VTube-STEP]] and [[VTube-LASER]] that can calculate the fixed and proportional springback values to be included in the Part Setup menu.<br><br> | + | The Overbend Calculator is a built-in feature in [[VTube-STEP]] and [[VTube-LASER]] that can calculate the fixed and proportional springback values to be included in the Part Setup menu or the Springback Table.<br><br> |
These values have an effect the final bend angles when sending new data to the bender, and when making corrections to the bender.<br><br> | These values have an effect the final bend angles when sending new data to the bender, and when making corrections to the bender.<br><br> | ||
</td> | </td> | ||
| Line 17: | Line 17: | ||
<tr> | <tr> | ||
</table> | </table> | ||
| + | |||
| + | |||
| + | ==Why Use Springback Compensation with Overbending?== | ||
| + | |||
| + | The springback feature is for predicting the amount of overbend necessary to compensate for springback. ("Overbend" is a term that we created and use to describe what happens in the springback compensation process. To compensate for springback, you overbend each bend.) The goal is to make the first part after the initial bender setup closer to the nominal.<br><br> | ||
| + | |||
| + | ===Traditional Fabrication=== | ||
| + | Traditionally customers just bent the first part without any springback compensation, then allowed VTube-LASER to correct the bender to bring the part close to the master data. For customers with inexpensive material and high-volume per-part production, this was not an issue. However, now more customers are starting to build up a database of springback information to drive the part more quickly to the master shape.<br><br> | ||
| + | |||
| + | ===The Springback Compensation Method=== | ||
| + | The '''method''' is to measure the characteristics of springback for a given material and bender setup '''using a test piece''', then store springback values that let VTube inject extra bend angle (and remove some straight distance between bends) to get to a part within the tolerance envelope ''more quickly''. See the steps for calculating springback values below.<br><br> | ||
| + | |||
| + | ===Justification for Using Springback Compensation=== | ||
| + | An increasing number of customers are asking if they should use springback compensation. Since there is a cost invested to bend and measure the test piece, each customer has a different trigger point for making springback compensation worth while.<br><br> | ||
| + | For industries with very expensive material, the justification for springback compensation is very high. For example, in nuclear shipbuilding applications, material costs of $1000 per foot require that the first part be within tolerance every time.<br><br> | ||
| + | To answer the question for your application, we recommend that you dedicate time to running time-studies to see at what point compensating for springback makes sense for your application.<br><br> | ||
| + | |||
| + | <br><br> | ||
==Steps to Calculate Springback Values== | ==Steps to Calculate Springback Values== | ||
| Line 49: | Line 67: | ||
===STEP 3=== | ===STEP 3=== | ||
The actual resulting bend angles are measured and entered into the Overbend Calculator.<br><br> | The actual resulting bend angles are measured and entered into the Overbend Calculator.<br><br> | ||
| − | If you're using VTube-LASER connected to a FARO measuring center, then you can create a part with the bend angles, then measure a test part, then copy the measured angles into the Overbend calculator. | + | If you're using VTube-LASER connected to a FARO measuring center, then you can create a part with the bend angles in the Bender Setup tab (the previous tab menu), then measure a test part, then copy the measured angles into the Overbend calculator. |
</td> | </td> | ||
<td> | <td> | ||
| Line 62: | Line 80: | ||
The proportional and fixed values are calculated and used in a springback formula to overcome springback at any angle by calculating the overbend angles.<br><br> | The proportional and fixed values are calculated and used in a springback formula to overcome springback at any angle by calculating the overbend angles.<br><br> | ||
Press the Calculate button to calculate the values.<br><br><br> | Press the Calculate button to calculate the values.<br><br><br> | ||
| − | After you | + | After you calculate the values, you can choose one of these actions... |
*Save the values to Part Setup and close the window.<br><br> | *Save the values to Part Setup and close the window.<br><br> | ||
*Add the values to the end of the Springback table and close the window.<br><br> | *Add the values to the end of the Springback table and close the window.<br><br> | ||
| Line 74: | Line 92: | ||
</table> | </table> | ||
| + | |||
| + | <br><br> | ||
==Where the Values are Stored in VTube== | ==Where the Values are Stored in VTube== | ||
| Line 101: | Line 121: | ||
</table> | </table> | ||
| − | ==Using Springback Values in VTube- | + | ==Using Springback Values in VTube-STEP to Change the Bender Setup== |
<table> | <table> | ||
| + | |||
<tr> | <tr> | ||
| − | <td width=400> | + | <td width=400 valign="top"> |
| − | These two calculated values will be used to calculate overbend to overcome springback when sending data to the bender in the '''BEND SETUP''' page in VTube-LASER. | + | ===METHOD 1: SUPRAVISION NETWORK PROTOCOL=== |
| + | These two calculated values will be used to automatically calculate overbend to overcome springback when sending data to the bender in the '''BEND OUTPUT''' Automated Supravision Link protocol menu in VTube-STEP.<br><br> | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:vtube-step_v2.2_benderoutput_SVnetwork.png|500px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | <tr> | ||
| + | <td width=400 valign="top"> | ||
| + | ===METHOD 2: EXPORTING TO A BENDER FILE=== | ||
| + | These two calculated values will be used to automatically calculate overbend to overcome springback when saving data to a bender file in the '''IMPORT/EXPORT''' menu.<br><br> | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:vtube-step_v2.2_export_menu.png|500px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | |||
| + | </table> | ||
| + | |||
| + | |||
| + | |||
| + | ==Using Springback Values in VTube-STEP Reports== | ||
| + | |||
| + | <table> | ||
| + | |||
| + | <tr> | ||
| + | <td width=400 valign="top"> | ||
| + | These two calculated values can be used to report bender with springback compensation.<br><br> | ||
| + | The springback values are used to adjust the length between bends and bend angles. | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:vtube-step_v2.2_springback_report.png|500px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | |||
| + | </table> | ||
| + | |||
| + | ==Using Springback Values in VTube-LASER to Change the Bender Setup== | ||
| + | |||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=400 valign="top"> | ||
| + | The VTube-LASER license level uses the FARO measuring center to measure and qualify a tube shape, then correct tube benders.<br><br> | ||
| + | The springback values can be used to automatically calculate overbend to overcome springback when sending setup data to the bender in the '''BEND SETUP''' page in VTube-LASER.<br><br> | ||
| + | This image shows the AUTO SEND button inside the Bender Setup menu in VTube-LASER. | ||
</td> | </td> | ||
<td> | <td> | ||
Latest revision as of 14:42, 1 June 2016
About Overbend Calculator
|
The Overbend Calculator is a built-in feature in VTube-STEP and VTube-LASER that can calculate the fixed and proportional springback values to be included in the Part Setup menu or the Springback Table. |
|
Why Use Springback Compensation with Overbending?
The springback feature is for predicting the amount of overbend necessary to compensate for springback. ("Overbend" is a term that we created and use to describe what happens in the springback compensation process. To compensate for springback, you overbend each bend.) The goal is to make the first part after the initial bender setup closer to the nominal.
Traditional Fabrication
Traditionally customers just bent the first part without any springback compensation, then allowed VTube-LASER to correct the bender to bring the part close to the master data. For customers with inexpensive material and high-volume per-part production, this was not an issue. However, now more customers are starting to build up a database of springback information to drive the part more quickly to the master shape.
The Springback Compensation Method
The method is to measure the characteristics of springback for a given material and bender setup using a test piece, then store springback values that let VTube inject extra bend angle (and remove some straight distance between bends) to get to a part within the tolerance envelope more quickly. See the steps for calculating springback values below.
Justification for Using Springback Compensation
An increasing number of customers are asking if they should use springback compensation. Since there is a cost invested to bend and measure the test piece, each customer has a different trigger point for making springback compensation worth while.
For industries with very expensive material, the justification for springback compensation is very high. For example, in nuclear shipbuilding applications, material costs of $1000 per foot require that the first part be within tolerance every time.
To answer the question for your application, we recommend that you dedicate time to running time-studies to see at what point compensating for springback makes sense for your application.
Steps to Calculate Springback Values
STEP 1Right click anywhere in the Part Setup menu and click on Overbend Calculator in the popup menu. |
|
STEP 2Set the bender to bend a two bend part.
|
|
STEP 3The actual resulting bend angles are measured and entered into the Overbend Calculator. |
|
STEP 4The proportional and fixed values are calculated and used in a springback formula to overcome springback at any angle by calculating the overbend angles.
|
|
Where the Values are Stored in VTube
Part SetupThe springback values are applied to the current project by storing the values in the Part Setup menu. |
|
Springback TableThe springback values can also be stored in the Springback Table so that you can reuse the values in other projects. |
|
Using Springback Values in VTube-STEP to Change the Bender Setup
METHOD 1: SUPRAVISION NETWORK PROTOCOLThese two calculated values will be used to automatically calculate overbend to overcome springback when sending data to the bender in the BEND OUTPUT Automated Supravision Link protocol menu in VTube-STEP. |
|
METHOD 2: EXPORTING TO A BENDER FILEThese two calculated values will be used to automatically calculate overbend to overcome springback when saving data to a bender file in the IMPORT/EXPORT menu. |
|
Using Springback Values in VTube-STEP Reports
|
These two calculated values can be used to report bender with springback compensation. |
|
Using Springback Values in VTube-LASER to Change the Bender Setup
|
The VTube-LASER license level uses the FARO measuring center to measure and qualify a tube shape, then correct tube benders. |
|
Other Pages
- Back to VTube-STEP
- Back to VTube-LASER
