Difference between revisions of "VTube NUMALLIANCE Bender Correction"
(→STEP 1) |
(→STEP 9) |
||
| (25 intermediate revisions by one user not shown) | |||
| Line 24: | Line 24: | ||
<td width=300> | <td width=300> | ||
| − | VTube-LASER has an export option for NUMALLIANCE | + | VTube-LASER has an export option for NUMALLIANCE MES files that are used to correct the NUMALLIANCE benders.<br><br> |
Note: NUMALLIANCE benders only require the ''measured'' data for corrections.<br><br> | Note: NUMALLIANCE benders only require the ''measured'' data for corrections.<br><br> | ||
Measure the tube in VTube-LASER, then send the MEASURED tube data to the bender control, and it will then perform the correction. | Measure the tube in VTube-LASER, then send the MEASURED tube data to the bender control, and it will then perform the correction. | ||
| + | <br><br> | ||
| + | Follow the steps below. | ||
</td> | </td> | ||
| Line 38: | Line 40: | ||
<br><br> | <br><br> | ||
| + | ==STEP 1== | ||
| + | <table cellpadding=10 width=1200> | ||
| + | <tr valign=top> | ||
| − | ==STEP | + | <td width=300> |
| + | Press the Bender Setup button. (These steps assume that you have measured the tube and have setup VTube-LASER with the NUMALLIANCE protocol.) | ||
| + | |||
| + | </td> | ||
| + | |||
| + | <td> | ||
| + | [[image:Numalliance1.png|800px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | ==STEP 2== | ||
| + | |||
| + | <table cellpadding=10 width=1200> | ||
| + | <tr valign=top> | ||
| + | |||
| + | <td width=300> | ||
| + | Set the bender number. It should say NUMALLIANCE like shown here. | ||
| + | <br><br> | ||
| + | If the data in the window is not correct, then import the data from the main VTube-LASER memory by clicking on "Setup this Window" then clicking on "Copy Master LRA to Setup LRA". | ||
| + | <br><br> | ||
| + | In the "Correct the Bender" menu, click on Auto Send. | ||
| + | <br><br> | ||
| + | A save file dialog will open and allow you to name the MES file on a thumb drive or on the network. This file will be imported into the NUMALLIANCE control. | ||
| + | |||
| + | </td> | ||
| + | |||
| + | <td> | ||
| + | [[image:Numalliance2.png|800px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | ==STEP 3== | ||
| + | |||
| + | <table cellpadding=10 width=1200> | ||
| + | <tr valign=top> | ||
| + | |||
| + | <td width=300> | ||
| + | At the NUMALLIANCE control, press the CAD button. | ||
| + | <br><br> | ||
| + | |||
| + | </td> | ||
| + | |||
| + | <td> | ||
| + | [[image:NumallianceCADbutton.png|800px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | ==STEP 4== | ||
| + | |||
| + | <table cellpadding=10 width=1200> | ||
| + | <tr valign=top> | ||
| + | |||
| + | <td width=300> | ||
| + | Press the XYZ/LRA button.<br><br> | ||
| + | </td> | ||
| + | |||
| + | <td> | ||
| + | [[image:NumallianceXYZLRA.png|800px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | ==STEP 5== | ||
| + | |||
| + | <table cellpadding=10 width=1200> | ||
| + | <tr valign=top> | ||
| + | |||
| + | <td width=300> | ||
| + | Press the File button. | ||
| + | <br><br> | ||
| + | Press the Import corrections button. | ||
| + | |||
| + | </td> | ||
| + | |||
| + | <td> | ||
| + | [[image:NumallianceFileAndImport.png|800px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | ==STEP 6== | ||
<table cellpadding=10 width=1200> | <table cellpadding=10 width=1200> | ||
| Line 46: | Line 144: | ||
<td width=300> | <td width=300> | ||
| − | + | Open the file from VTube. | |
</td> | </td> | ||
<td> | <td> | ||
| − | [[image: | + | [[image:NumallianceOpenMESfile.png|800px]] |
</td> | </td> | ||
</tr> | </tr> | ||
Latest revision as of 23:29, 25 November 2019
|
This page describes how to use VTube-LASER to correct NUMALLIANCE benders. |
Back to VTube-LASER
Contents |
NUMALLIANCE CORRECTIONS
|
VTube-LASER has an export option for NUMALLIANCE MES files that are used to correct the NUMALLIANCE benders. |
|
STEP 1
|
Press the Bender Setup button. (These steps assume that you have measured the tube and have setup VTube-LASER with the NUMALLIANCE protocol.) |
|
STEP 2
|
Set the bender number. It should say NUMALLIANCE like shown here.
|
|
STEP 3
|
At the NUMALLIANCE control, press the CAD button.
|
|
STEP 4
|
Press the XYZ/LRA button. |
|
STEP 5
|
Press the File button.
|
|
STEP 6
|
Open the file from VTube. |
|
Other Pages
- See VTube-LASER
- See VTube-STEP
