Difference between revisions of "CNC Bender v11-20080923"
From ATTWiki
| (4 intermediate revisions by one user not shown) | |||
| Line 9: | Line 9: | ||
=CHANGES to CNC BENDER= | =CHANGES to CNC BENDER= | ||
| − | ===[[image:Check.jpg|25px]] REPAIR - Collision Detection Logic in CNC Processor Repaired === | + | ===[[image:Check.jpg|25px]] REPAIR - Collision Detection Logic in CNC Processor Repaired for Inputs === |
[[image:Momemtum_modicon.jpg]]<br> | [[image:Momemtum_modicon.jpg]]<br> | ||
| Line 17: | Line 17: | ||
===[[image:Check.jpg|25px]] ENHANCED - "Ranger Error" is now changed to "Collision" === | ===[[image:Check.jpg|25px]] ENHANCED - "Ranger Error" is now changed to "Collision" === | ||
| − | + | ||
CNC Processor now reports a potential "collision" rather than a "ranger error" in the logs. We felt that this is clearer English. | CNC Processor now reports a potential "collision" rather than a "ranger error" in the logs. We felt that this is clearer English. | ||
<br><br> | <br><br> | ||
===[[image:Check.jpg|25px]] ENHANCED - Relative Bend Arm Behavior Changed === | ===[[image:Check.jpg|25px]] ENHANCED - Relative Bend Arm Behavior Changed === | ||
| − | In previous versions, CNC Bender would stop any process that tried to send the bend arm into the negative region. | + | In previous versions, CNC Bender would stop any process that tried to send the bend arm into the negative region.<br> |
| + | [[image:Bendarm_pines_236.jpg]] | ||
<br><br> | <br><br> | ||
CNC Bender now automatically adjusts the bend arm motion if the operator instructs the axis to go further than 0 (into the negative region) with any controlled motion (including controlled jogs). | CNC Bender now automatically adjusts the bend arm motion if the operator instructs the axis to go further than 0 (into the negative region) with any controlled motion (including controlled jogs). | ||
<br><br> | <br><br> | ||
| − | ===[[image:Check.jpg|25px]] REPAIR - PDA Axis Safe Mode Auto Recovery === | + | ===[[image:Check.jpg|25px]] REPAIR - PDA GEARED Axis Safe Mode Auto Recovery === |
| + | [[image:Cncbender_pda_rvg_icon_large.jpg ]]<br> | ||
A Pressure Die Assist axis now participates in the Safe Mode Motion Auto Recovery when it is geared. | A Pressure Die Assist axis now participates in the Safe Mode Motion Auto Recovery when it is geared. | ||
<br><br> | <br><br> | ||
Latest revision as of 04:34, 26 September 2008
Contents |
This is mainly a set of debug changes to CNC Bender.
CHANGES to CNC BENDER
REPAIR - Collision Detection Logic in CNC Processor Repaired for Inputs
CNC Processor was corrected to examine the second register (or bank) of 16 points on a 32 bit module.
ENHANCED - "Ranger Error" is now changed to "Collision"
CNC Processor now reports a potential "collision" rather than a "ranger error" in the logs. We felt that this is clearer English.
ENHANCED - Relative Bend Arm Behavior Changed
In previous versions, CNC Bender would stop any process that tried to send the bend arm into the negative region.
CNC Bender now automatically adjusts the bend arm motion if the operator instructs the axis to go further than 0 (into the negative region) with any controlled motion (including controlled jogs).
REPAIR - PDA GEARED Axis Safe Mode Auto Recovery
A Pressure Die Assist axis now participates in the Safe Mode Motion Auto Recovery when it is geared.
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
